Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 20

Страница: 20 / 74

Electric Drives

and Controls

3–1

Bosch Rexroth AG

Servodyn-D

1070 066 032 / 03

Marks, certifications

Marks, certifications

3.1

CE-marking

Low-Voltage Directive

The CE marking confirms compliance of drive modules of the Servodyn-

D series with the Low-Voltage Directive. The rating and construction sat-

isfy the requirements of EN 50178.

Machinery Directive

The CE marking confirms compliance of drive modules of the Servodyn-

D series with the Machinery Directive. The rating and construction sat-

isfy the requirements of EN 60204-1.

EMC Directive

Concerning the EMC Directive, the exception stipulated in the German

EMC Act, EMVG Art. 6, Subs. (9), is applicable, cf. below.

The following must be noted with respect to the operational system (cf.

EMC manual):

Requirements on EMC noise emission

Conducted noise

Depending on the application (industrial environment or domestic

application), a suitable mains filter is to be provided in the power

supply line.

The cubicle construction should be designed so as to ensure the

efficiency of the mains filter to the greatest possible extent.

Radiated noise

Depending on the application (industrial environment or domestic

application), a suitable switch cabinet with EMC shielding has to

be provided.

For the motor leads, shielded cables should be preferably used

which are grounded on both ends of the shield.

Required interference immunity

The rating and construction satisfy the requirements of the EMC

product standard EN 61800-3 for application in industrial environ-

ments.

EMVG 18.09.1998
Art. 6 Exceptions and special determinations

(9)Apparatuses, systems, and components covered by Subs. 3, which

are exclusively manufactured and designed as accessories or spare

parts for further processing by companies or persons with expert

knowledge in the field of electromagnetic compatibility, are exempted

from compliance with the protection requirements and the require-

ments of Art. 4 Subs. 1 Nos. 1 to 3 and 5. The operational unit which

contains apparatuses, systems or components defined in the 1

sen-

tence above, shall satisfy the provisions of this law.

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 20 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: