Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 30

Страница: 30 / 74

Electric Drives

and Controls

4–7

Bosch Rexroth AG

Servodyn-D

1070 066 032 / 03

VMA..KR, VMA..B,C,D,F and DM/DS error displays

Displays flash

alternately.

Action

Error

The drive has switched off.

Normal operation:

Maximum speed exceeded (channel 2)

The speed limit value S-0-0091 was ex-

ceeded.

Special operating mode (RSU):

Deviation from Safe Standstill

(channel 2)

The angle of rotation limit value

P-0-0022 was exceeded.

Special mode with acknowledgement

(RSU):

Deviation from Safe Speed

(channel 2)

The speed limit value P-0-0012 was ex-

ceeded.

Observe speed limit

Observe sequence of operations

Check enable signals

Check control circuits

Clear error by a RESET on the DM,

re-initialize SERCOS ring.

Activate mains contactor with “Drive

On”.

Replace VM if DMs and VM display the

error simultaneously

Check whether the fan on the bot-

tom side of the module has failed.

Charging circuit overloaded

Energy loss in the charging resistors too

high. Short circuit in DC link.

Check wiring with “DC link connection

terminal” in place

Switch back on after approx. 5 min.

Replace mains connection module

Replace EBX module

Line reactor connection

The line reactor is incorrectly con-

nected.

Possible interaction with F22: Switch

back on after 16 seconds

Check line reactor connection

Observe waiting time for reconnection

(> 16 sec)

Charging circuit defective

Line contactor K1 in the mains connection

module is not energized.

The display may change to F21 if switched

back on within 16 sec.

Set rotary switch S1 on VM to values >

Observe waiting time for reconnection

(> 16 sec)

Replace mains connection module

No DC link controller

DC link cannot be adjusted according to

setpoint.

Replace supply module

Main contactor is not energized

Replace mains connection module

Main contactor released

The main contactor was released during

operation.

Replace mains connection module

Main contactor is not released

Replace mains connection module

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 30 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: