Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 21

Страница: 21 / 74

3–2

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

Marks, certifications

3.2

EU design type certification

The certification covers Servodyn-D with redundant safety monitoring

RSU. RSU complies with the requirements concerning:

Safety-relevant parts of controllers

in accordance with EN 954-1

Category 3, as required by

EN 12415 (safety of turning machines)

EN 12417 (safety of machining centres)

Control functions in the event of a fault

according to EN 60204-1

In the special mode, the integrated 2-channel safety structure monitors

all axis and spindle movements. It is available for:

Three-phase modules with SERCOS interface

(firmware release as of V0.040)

in connection with supply modules with energy recovery capability

(firmware release as of V0.040) and

mains connection module NAA

This concept has been certified, i.e. additional monitoring equipment is

not necessary.

For more information, refer to Servodyn-D with Redundant Safety

Monitoring manual, part no. in Section 1.6.

NAA mains con-

nection module

Supply module VM

with sinusoidal infeed

and recovery

Three-phase current

module DM

Separating protective

device

Three-phase mains

Safety

tumbler

Module crosscon
nection

Integration of an EMERGENCY-

STOP switch

Connection and monitoring of a

mode selector switch

Connection and monitoring of a

dead-man’s key

Integrated line monitor for single

and multiple phase mains failures

Integrated control and monitoring

of the protective door tumbler

Safe reduced speed in special mode

Safe standstill in special mode

Monitoring of the maximum speed

Mains contactor control

Motor

Sercodyn-D concept

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 21 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: