Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 15

Страница: 15 / 74

1–10

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

Safety Instructions

Release

The present manual applies to the following releases:

DM/DS software:

SERCOS interface

V0.049 or higher

CANopen/rho

V0.002 or higher

Analog interface

V0.17 or higher

PROFIBUS-DP

V0.004 or higher

Motion Control

V0.010 or higher

VM software:

V0.045 or higher

The current software release number can be viewed by selecting

parameter S-0-0030 with the DSS-D Commissioning and Service

System, or in the ”Software” field of the module configuration display

(DIAGNOSTICS

MODULE CONFIGURATION).

For information concerning the current DSS software release, refer to

HELP

ABOUT...

The current software release of VMA..KR and VMA..B,C,D,F can

only be read from the 7-segment display during test operation. For

this purpose, turn dip switch ”T” on the VM’s personality module ”on”:

The following appears in a running, flashing display:

“

Cxx.ZZ.ddmmyyyy

“

Where:

= software release number

= (internal)

= software creation day

= software creation month

yyyy

= software creation year

Trademarks

All trademarks of software installed on Rexroth products upon delivery

are the property of the respective manufacturer.

Upon delivery, all installed software is copyright-protected. The software

may only be reproduced with the approval of Rexroth or in accordance

with the license agreement of the respective manufacturer.

MS-DOS

and Windows

are registered trademarks of Microsoft

Corporation.

PROFIBUS

is a registered trademark of the PROFIBUS Nutzerorgani-

sation e.V. (user organization).

SERCOS interface

is a registered trademark of Interessengemeins-

chaft SERCOS interface e.V. (Joint VDW/ZVEI Working Committee).

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 15 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: