Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 35

Страница: 35 / 74

4–12

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

VMA..KR, VMA..B,C,D,F and DM/DS error displays

Displays flash

alternately.

Action

Error

The drive has switched off.

Assignment mains connection mod-

ule – VM

Mains connection module and supply mod-

ule do not have the same power output

stage.

Combine compatible modules

CAN bus only:

Internal command active

The controller must not enable the drive at

this time.

Runtime Personality Module

Check stable position of personality

module

Replace personality module

Runtime I

C-Bus

Replace module

Stacking error

Replace module

Inadmissible memory access

Replace module

Synchronization error I controller

Internal synchronization of the VM firm-

ware disturbed

Replace module

Speed controller plausibility error

For details of the fault, refer to

S-0-0095, cf. page 4–14.

Check motor cable

Switch modules off because of

danger-

ous

electrical voltage!

Check DC link connection,

check DC link voltage

Motor stalled

Turn off torque reduction

For more details, refer to P-0-0010

VM error

Torque is immediately turned off because

of an operating fault (e.g. under-/overvol-

tage)

Check error message on VM

Clear error by “Reset Diagnostics class

1 error”

Check whether the fan on the bot-

tom side of the module has failed.

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 35 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: