Black Box IPBX1224 страница 19 Скачать руководство пользователя

Страница: 19 / 52

724-746-5500 | blackbox.com

Page 19

Chapter 3: Installation

• If installing Scenario 2, connect the Ethernet Port 4 to the ISP’s router/switch.

Connect the FXO ports

• Connect the analog phone lines supplied by your phone company to the FXO ports. You will need to use line splitters since

each port supports two lines.

• To support failover, make sure that you connect an analog line to:

• FXO1 on the IPBX424

• FXO9 on the IPBX1224

Connect the FXS ports

• On the IPBX424, connect an analog phone to FXS1. During a power failure, FXS1 is bridged to FXO1, allowing you to make

analog phone calls. Connect another analog device (such as a fax machine), to FXS2.

• On the IPBX1224, connect an analog phone to FXS2. During a power failure, FXS2 is bridged to FXO9, allowing you to make

analog phone calls. Connect another analog device (such as a fax machine), to FXS1.

Connect audio ports

• Connect the Audio In port to an external audio source (to provide music on hold).

• Connect the Audio Out port to a paging system.

3.2.3 STEP 3: Run the setup wizard

The Hybrid PBX and VoIP Gateway is configured using its Web-based command center that you access using the Web browser on
your computer. For requirements, see Section 3.2.1, STEP 1D: Configure your computer.

NOTE: The setup wizard only runs the first time you start the command center after a factory reset.

To start the setup wizard:

Specify http://192.168.1.2 in the address bar of your browser and press “Enter.” The Start page for the Setup Wizard opens.

Содержание IPBX1224





















































Результаты поиска

Содержание IPBX1224

Отзывы:

Похожие инструкции для IPBX1224

Бренды по названию

Популярные бренды

Black Box IPBX1224, Руководство по установке

Результаты поиска

Содержание IPBX1224

Отзывы:

Похожие инструкции для IPBX1224

Бренды по названию

Популярные бренды