Black Box IPBX1224 страница 11 Скачать руководство пользователя

Страница: 11 / 52

724-746-5500 | blackbox.com

Page 11

Chapter 2: Overview

2.4.3 Hardware Features

This section describes the key hardware features of the Hybrid PBX and VoIP Gateway.

Front-panel status lights

Figure 2-5. Front-panel status lights.

Table 2-3. Front-panel status LEDs.

LED

Status

Description

FXO

Off

The corresponding FXO port is not connected, or is connected to an analog phone line that is not operational.

The corresponding FXO port is connected, or is connected to an analog operational phone line.

Circle

Off

The Hybrid PBX and VoIP Gateway is off.

Blinking

The Hybrid PBX and VoIP Gateway is starting up.

The Hybrid PBX and VoIP Gateway is fully operational.

All lights

The Hybrid PBX and VoIP Gateway is not operational because of a fault. Possible causes include: incompatible
USB auxiliary memory device is installed, corrupt firmware, or hardware failure.

Ethernet port status lights

Each Ethernet port has two status lights.

Table 2-4. Ethernet port status lights.

LED

Status

Description

Left

Off

Port is operating at 10 Mbps.

Port is operating at 100 Mbps.

Right

Off

The port is not connected.

Blinking

The port is sending/receiving data.

The port is connected.

USB ports

Both PBX models have two USB ports.

• One port can be used to connect auxiliary memory in the form of a USB drive. This provides additional storage for voicemail, call

recordings, and log files. Only one auxiliary memory device is supported at a time. For more information, see Section 3.2.1, Step
1C.

Содержание IPBX1224





















































Результаты поиска

Содержание IPBX1224

Отзывы:

Похожие инструкции для IPBX1224

Бренды по названию

Популярные бренды

Black Box IPBX1224, Руководство по установке

Результаты поиска

Содержание IPBX1224

Отзывы:

Похожие инструкции для IPBX1224

Бренды по названию

Популярные бренды