2
3
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including the
following:
1. Before connecting the heater, check that the
voltage indicated on the rating plate corresponds
to the main voltage in your home/office.
2.
WARNING:
In order to avoid overheating,
do not cover the heater (
).
3. DO NOT position the heater directly under a
power socket.
4. Do not use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
5. If the supply cord or plug is damaged, it must
be replaced by the manufacturer or its service
agent or similarly qualified person in order to
avoid hazard. The heater contains no user
serviceable parts. Should the product suffer
damage or breakdown, it must be returned to
the manufacturer or their service agent.
6. Under the environment with electrical fast
transient, the product may malfunction and
require user to reset the product.
7. Do not use this heater with a programmer, timer
or any other device that switches the heater on
automatically, since a fire risk exists if the heater
is covered or positioned incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT use this heater outdoors.
10. DO NOT position where it can be touched by
children, especially the very young.
11. Allow a safe area around the heater away from
furniture or other objects; at least 50 cm from
the top and sides and 200 cm at the front.
12. Do not use this heater when it is lying on its side.
13. DO NOT use the heater in rooms with
explosive gas (e.g. petrol) or while using
inflammable glue or solvent (e.g. when gluing
or varnishing parquet floors, PVC etc).
14. DO NOT insert any objects into the heater.
15. Keep the mains cord at a safe distance from
the main body of the heater. Turn off and
unplug heater when not in use and before
cleaning.
16. If overheating should occur, the built-in
overheating safety device will switch off the
heater.
17. Do not place the cord under a rug.
18. The heater cannot be used adjacent to
curtains or combustible material. Curtains or
combustible material may be burned if the
heater was installed incorrectly.
19. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
20.
WARNING:
Risk of Fire. Discontinue
use if the outlet or plug become hot to the
touch. Overheating may indicate a worn
or damaged outlet. Consult a qualified
electrician for outlet replacement.
21.
CAUTION:
In order to avoid a hazard due
to inadvertent resetting of the thermal cutout,
this appliance must not be supplied through
an external switching device, such as a timer,
or connected to a circuit that is regularly
switched on and off by the utility.
DESCRIPTIONS (See Fig. 1, 2, 3 & 4)
A. Rear Base
B. Power Cord
C. Base Securing Screws (4)
D. Front Base
E. Control Panel
F. Remote Control
G. Assembled Base
H. Indicator Lights
I. Power Button
J. Energy Saving Button
K. Fan Only Button
L. Timer Button
M. Thermostat Button
N. Oscillation Button
O. LCD Display
ASSEMBLY INSTRUCTIONS
NOTE:
A Phillips screwdriver is required for assembly.
Unpack your heater from the box, being careful
to remove all parts from plastic bags and
remaining packaging. Please save the carton for
off-season storage.
This model is packed with separate base in the
box. Carefully remove all parts from plastic bags.
To prevent scratches, place all parts onto a cloth
before assembly. Follow the below instructions
for Base assembly:
Base Assembly
Step 1: Snap the two halves of the base together
and run the power cord through the
center of the base. Line up holes of the
base with holes on bottom of heater
housing, and secure with 4 provided
screws. (Refer to Fig. 1)
Step 2: Lace the power cord through the cord
minders on the underside of the base.
(Refer to Fig. 2)
Step 3: Turn the heater right side up on a flat
level surface prior to beginning operation.
(Refer to Fig. 3)
Remote Control
Your heater comes with a remote control, unpack
the remote control from box. This unit requires
two (2) AAA batteries, 1.5V (not included). Please
note this remote control will not work through
walls.
Battery Replacement
a) Remove battery cover from remote control.
b) Remove batteries from the remote control.
c) Insert two new batteries, pressing them firmly
into their slot.
d) Replace the battery cover.
NOTES:
• Replace all batteries of a set at the same time.
• Being careful not to bend or damage the
contact spring, clean the battery contacts and
the devices’ contacts prior to installing the
batteries.
• Remove the batteries from the equipment
when it is not being used for an extended
period of time.
• Remove the used batteries promptly.
• Do not mix old and new batteries. Do not
mix alkaline, standard, (carbon-zinc), or
rechargeable batteries.
• Do not discard used batteries into
household trash containers. Contact your
local governments for disposal or recycling
practices in your area.
The remote control for this unit has the capability
of operating all control panel functions. Please
note this remote control will not work through
walls.
OPERATING INSTRUCTIONS
1. Plug heater into a standard outlet. Once
plugged in, the Power Light will illuminate,
and the room temperature will appear on the
LCD Display.
2. Operate heater by pressing the Power Button
( ) and selecting modes and settings
according to preference.
NOTE:
Remove the plastic film from the
control panel before using (if included).
Power Button
Press the Power Button ( ) to turn the heater
on. Once on, the heater will run in the
Max Heat
mode and the
Stay On
icon will appear on the
LCD Display. Press the Power Button ( ) to
manually turn off the heater at any setting.
NOTE:
The Power Light will remain illuminated
while unit is plugged in.
Mode Selection
Select your desired heat settings by pressing the
corresponding buttons as located on your heater
or remote control. An indicator light will illuminate
next to each button to indicate that the selected
setting/mode is activated.
Fan Only Setting
Press the
Fan Only
Button to run the heater
without heat output. The
Stay On
icon will
appear on the LCD Display.
Energy Saving Setting
Press the
Energy Saving Button
( ) to activate
the energy efficient Mode. The heater will now
cycle between high (at 2500W) and low (at
1250W) heat settings to provide heat. The
Stay
On
icon will appear on the LCD Display.
Thermostat Control
Your heater is equipped with a digital thermostat
that allows you to set your heater to the desired
comfort level by pressing the Thermostat Button
( ) on the control panel or remote control:
NOTE:
The
Thermostat icon
( ) will appear
on the LCD Display.
To preset a comfort level, press the Thermostat
Button ( ) to adjust the temperature from from
18°C
to
30°C
(Default:
18°C
, and each press of
the button will scroll through the next
temperature level). The LCD Display will show
the selected temperature reading. When the
preset temperature is reached, the heater will
shut off and cool down for 15 seconds. When the
room temperature drops below the preset
temperature, the heater will automatically turn on
again to maintain the preset temperature level.
ENGLISH
Fig. 4
BCH9300
A
B
B
C
D
F
E
G
H
I
I
J
J
K
K
L
L
M
M
N
N
O
Fig. 3
Fig. 1
Fig. 2
BCH9300-050_12MLM1.indd 4-6
5/8/12 11:08 AM
