BFT LEO B CBB DL2 3 120 F02 PHOT USA16, Руководство по установке

Страница: 34 / 80

INSTALLATION MANUAL
2) GENERAL INFORMATION
The LEO B CBB DL2 3 230 L02 - LEO B CBB DL2 3 120 F02- LEO B CBB DL2 3
120 F02 PHOT USA16 control panel comes with standard factory settings. Any
change must be made using the programmer with built-in display or universal
handheld programmer. The Control unit completely supports the EELINK protocol.
Its main features are:
- Control of 1 single-phase motor
- Electronic torque control
- Obstacle detection
- Separate inputs for safety devices
- Con fi gurable command inputs
- Built-in radio receiver rolling code with transmitter cloning.
The board has a terminal strip of the removable kind to make maintenance
or replacement easier. It comes with a series of prewired jumpers to make the
installer’s job on site easier.
The jumpers concern terminals: 70-71, 70-72, 70-74, 76-77. If the above-
mentioned terminals are being used, remove the relevant jumpers.
LEO B CBB DL2
3 230 L02
LEO B CBB DL2 3
120 F02
LEO B CBB DL2 3 120
F02 PHOT USA16
Power supply 220-230V~
50Hz/60Hz
120V~ ±10%
50Hz/60Hz
120V~ ±10%
50Hz/60Hz
Obstacle
detection with
encoder
Present
Present
Only for sw versions
7.08
Present
Only for sw versions
8.08
Output for
terminals 26-27:
N.O. contact
(24V~/0,5A)
AUX3
con fi gurable
AUX3 con fi gurable
Output for audible
signal
TESTING
The
LEO B CBB DL2 3 230 L02 - LEO B CBB DL2 3 120 F02- LEO B CBB DL2 3
120 F02 PHOT USA16 panel controls (checks) the start relays and safety devices
(photocells) before performing each opening and closing cycle.
If there is a malfunction, make sure that the connected devices are working
properly and check the wiring.
3) TECHNICAL SPECIFICATIONS
Power supply
220-230V~ 50Hz/60Hz
(LEO B CBB DL2 3 230 L02)
120V~ ±10% 50Hz/60Hz
(LEO B CBB DL2 3 120 F02/ LEO B CBB DL2
3 120 F02 PHOT USA16)
Low voltage/mains insulation > 2MOhm 500V
Operating temperature range -20 / +55°C
Thermal overload protection Built into motor
Dielectric rigidity mains/LV 3750V~ for 1 minute
Maximum motor power 750W
Accessories power supply
24V~ (demand max. 1A)
24V~safe
AUX 0
220-230V~N.O. (40W max)
(LEO B CBB DL2 3 230 L02)
powered contact
120V~N.O. (40W max)
(LEO B CBB DL2 3 120 F02/ LEO B CBB DL2
3 120 F02 PHOT USA16)
powered contact
AUX 3/ Output for audible signal NO contact (24V~/max.0,5A)
Dimensions 146x170x60mm
Fuses see
Fig. B
N° of combinations 4 billion
Max.n° of transmitters that can be memorized 63
Usable transmitter versions:
All ROLLING CODE transmitters compatible with
4) TUBE ARRANGEMENT Fi g. A
5) TERMINAL BOARD WIRING Fig. B
WARNINGS - When performing wiring and installation, refer to the standards in
force and, whatever the case, apply good practice principles.
Wires carrying di ff erent voltages must be kept physically separate from each other,
or they must be suitably insulated with at least 1mm of additional insulation.
Wires must be secured with additional fastening near the terminals, using devices
such as cable clamps.
All connecting cables must be kept far enough away from the dissipater.
Terminal De fi nition Description
Po
w
er
supply
L LINE
Single-phase power supply
220-230V
~
50/60Hz
, with earth cable
(LEO B CBB DL2 3 230 L02).
Single-phase power supply 120V~ ±10%, 50-60Hz, with earth cable
(LEO B CBB DL2 3 120 F02/ LEO B CBB DL2 3 120 F02 PHOT USA16).
N NEUTRAL
GND EARTH
M
ot
or
10 START + CAP
Motor connection.
START + CAP Motor Start and capacitor
COM Motor Common
START + CAP Motor Start and capacitor
11 COM
12 START + CAP
A
ux
20
AUX 0 - POWERED CONTACT
220 230V~
(LEO B CBB DL2 3 230 L02)
POWERED CONTACT 120V~
(LEO B CBB DL2 3 120 F02)
(LEO B CBB DL2 3 120 F02 PHOT USA16)
AUX 0 con fi gurable output - Default setting FLASHING LIGHT.
MONOSTABLE RADIO CHANNEL/ SCA GATE OPEN LIGHT/ COURTESY LIGHT command/ ZONE LIGHT command/ STAIR LIGHT/
GATE OPEN ALARM/ FLASHING LIGHT/ SOLENOID LATCH/ MAGNETIC LOCK/ MAINTENANCE/ FLASHING LIGHT AND MAINTE-
NANCE / ANTITAMPERING / GATE STATUS / BISTABLE RADIO CHANNEL / TIMED RADIO CHANNEL.
Refer to “AUX output con fi guration” table.
21
26
AUX 3 - FREE CONTACT (N.O.)
LEO B CBB DL2 3 230 L02
LEO B CBB DL2 3 120 F02
AUX 3 con fi gurable output - Default setting MONOSTABLE RADIO CHANNEL Output.
MONOSTABLE RADIO CHANNEL/ SCA GATE OPEN LIGHT/ COURTESY LIGHT command/ ZONE LIGHT command/ STAIR
LIGHT/ GATE OPEN ALARM/ FLASHING LIGHT/ SOLENOID LATCH/ MAGNETIC LOCK/ MAINTENANCE/ FLASHING LIGHT AND
MAINTENANCE / GATE STATUS / BISTABLE RADIO CHANNEL / TIMED RADIO CHANNEL.
Refer to “AUX output con fi guration” table.
27
26
OUTPUT CONFIGURED AS UL
ALARM
LEO B CBB DL2 3 120 F02 PHOT
USA16
Activation: 2 consecutive obstacle detections uninterrupted by an end stop
Deactivation: after 300s or after removal of the “STOP” input
27
Mo
to
r
lim
it
sw
itc
h
1 (mo
del not
UL
TR
A)
41 + REF SWE Limit switch common
42 SWC Closing limit switch SWC (N.C.). (Do not connect or jump if there is the magnetic limit switch)
43 SWO - Opening limit switch SWO (N.C.). (NDo not connect or jump if there is the magnetic limit switch)
Mo
to
r
m
ag
ne
tic
limit swit
ch 1
JP32 Magnetic limit switch connection
A
cc
essories po
w
er
supply
50 24V-
Accessories power supply output.
51 24V+
52 24 Vsafe+
Tested safety device power supply output (photocell transmitter and safety edge transmitter).
Output active only during operating cycle.
Commands
60 Common IC 1 and IC 2 inputs common
61 IC 1
Con fi gurable command input 1 (N.O.) - Default START E.
START E / START I / OPEN / CLOSE / PED / TIMER / TIMER PED
Refer to the “Command input con fi guration” table.
62 IC 2
Con fi gurable command input 2 (N.O.) - Default PED.
START E / START I / OPEN / CLOSE / PED / TIMER / TIMER PED
Refer to the “Command input con fi guration” table.
63 Common IC 3 and IC 4 inputs common
64 IC 3
Con fi gurable command input 3 (N.O.) - Default OPEN.
START E / START I / OPEN / CLOSE / PED / TIMER / TIMER PED
Refer to the “Command input con fi guration” table.
65 IC 4
Con fi gurable command input 4 (N.O.) - Default CLOSE.
START E / START I / OPEN / CLOSE / PED / TIMER / TIMER PED
Refer to the “Command input con fi guration” table.
WIRING AND TERMINAL BOARD CONFIGURATION
34 -
LEO B CBB DL2 3 230 L02-LEO B CBB DL2 3 120 F02- LEO B CBB DL2 3 120 F02 PHOT USA16
D812916 00100_02