Belfort AWOS Скачать руководство пользователя | Manualshive

Страница: 25 / 95

background image

-22-

BELFORT

INSTRUMENT

Proprietary Information

5.5

W

IND

S

PEED SENSOR

– A

NNUAL

V

ERIFICATION

P

ROCEDURE

The wind speed sensor verification procedure is a confidence test, which verifies that the Belfort
AWOS wind speed readings compare reasonably with measurements taken from a reference
Kestrel Model 3000 Wind Instrument.

SAFETY PRECAUTIONS

1. Before starting any power installation tasks, ensure that the A/C power circuit breaker is in the

open position.

2. Do not perform outdoor Belfort AWOS installation tasks during a thunderstorm.
3. Use extreme caution when lowering the tilt-over tower whenever ice or snow has accumulated

on the tower cross arm or the sensors. The extra weight may cause the tower to fall over
rapidly.

PARTS AND TOOLS REQUIRED

1.

Belfort AWOS Hand Held Display Unit (HHDU)

2.

Kestrel Model 3000 Wind Instrument

VERIFICATION INSTRUCTIONS

1.

Turn on the HHDU. Stand near the base of the Belfort AWOS tower, facing into the wind.
Observe the Belfort AWOS wind indicator vane to ascertain wind direction.  Turn on the
Kestrel  Model  3000,  select  average  mode,  and  hold  the  Kestrel  Model  3000  as  high  as
possible,  square  to  the  wind  for  approximately  one  minute.    Observe  the  average  on  the
Kestrel and compare it to the wind speed measured by the Belfort AWOS and displayed on
the HHDU.  Press refresh to  get  the most recent  HHDU data.   The  wind  speed readings
should agree within 20% for speeds above 5 knots.

2.

If the readings do not agree within 20%, the wind speed sensor should be replaced.

Follow

the Belfort AWOS System Component Failure Instructions in Section 5.10.

«
...
23
24
25
26
27
...
»

Содержание AWOS
































































































Отзывы:

Нет отзывов

Похожие инструкции для AWOS

Бренд: Techno Line Страницы: 39

Бренд: YTORA Страницы: 8

Бренд: La Crosse Technology Страницы: 8

Бренд: Curtis Страницы: 11

Бренд: XFARM Страницы: 56

Docking Station

Бренд: Mi-Football Страницы: 8

Бренд: Goodmans Страницы: 10

Бренд: iPort Страницы: 2

Бренд: iPort Страницы: 24

Бренд: iHome Страницы: 12

Бренд: Electronic.Star Страницы: 10

Бренд: La Crosse Technology Страницы: 6

Бренд: La Crosse Technology Страницы: 28

Бренд: La Crosse Technology Страницы: 19

Бренд: Sony Ericsson Страницы: 36

Бренд: Sabrent Страницы: 16

Бренд: La Crosse Technology Страницы: 24

Бренд: Janam Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды