manualshive.com logo in svg

Belfort AWOS, Руководство по обслуживанию

Поделиться
Скачать
Belfort AWOS Скачать руководство пользователя страница 30

-27- 

BELFORT

 

INSTRUMENT 

Proprietary Information

 

10.

 

Open  the  power  enclosure  and  assure  that  both  function  lamps  on  the  surge  protector  are 
illuminated, if not, replace the surge protector. 

 

 
5.8

 

 

T

HE 

UHF

 

T

RANSCEIVER 

A

NNUAL 

M

AINTENANCE

  

 
The UHF transceiver operates under License from the Federal Communications Commission.  
The FCC Registration number is 0011055407.   The Emission Designator is 11K0F1D.  The 
operating specifications for the UHF Transceiver are located in Appendix C. 
 
The purpose of this testing is to verify that the UHF Transceiver is operating within 
specifications.  Four operating specifications are checked: Frequency, Power, Deviation, and 
VSWR.  The tolerance for each is located in Appendix C.  If the UHF transceiver is found to not 
be operating within the tolerances, the DCP will need to be returned to the Belfort Instrument 
factory for repair.  

Follow the Belfort AWOS System Component Failure Instructions in 

Section 5.10.

 

 

*Per FAA Circular 150/5220-16D, section 2.9.a, all maintenance technicians must meet the 
qualifications defined in FAA Order 6700.20, Non-Federal Navigational Aids and Air 
Traffic Control Facilities, in order to perform the Belfort AWOS Commissioning / Annual 
Inspection Procedure. 

 
Perform the Belfort AWOS Commissioning / Annual Inspection Procedure provided in 
Appendix E.  Complete the Belfort AWOS Commissioning / Annual Inspection Record Data 
Sheet during the test. 
  
 
 
5.9

 

 

T

HE 

VHF

 

U

NICOM 

R

ADIO 

A

NNUAL 

M

AINTENANCE

  

 

The VHF Unicom operates under License from the Federal Communications Commission.  The 
FCC License is specific for each Airport.  The operating specifications for the VHF Unicom 
Radio are located in Appendix D. 
 
The purpose of this testing is to verify that the VHF Unicom Radio operating within 
specifications.  Four operating specifications are checked: Frequency, Power, Deviation, and 
VSWR.  The tolerance for each is located in Appendix D.   
 

*Per FAA Circular 150/5220-16D, section 2.9.a, all maintenance technicians must meet the 
qualifications defined in FAA Order 6700.20, Non-Federal Navigational Aids and Air 
Traffic Control Facilities, in order to perform the Belfort AWOS Commissioning / Annual 
Inspection Procedure. 
 

 
Perform the Belfort AWOS Commissioning / Annual Inspection Procedure provided in 
Appendix E.  Complete the Belfort AWOS Commissioning / Annual Inspection Record Data 
Sheet during the test. 
 

Содержание AWOS
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды