manualshive.com logo in svg

Belfort AWOS, Руководство по обслуживанию

Поделиться
Скачать
Belfort AWOS Скачать руководство пользователя страница 39

-36- 

BELFORT

 

INSTRUMENT 

Proprietary Information

 

beginning  this  maintenance  tasks.    Refer  to  the  "Belfort  AWOS  Operator  Manual"  for 
instructions on how to enter and delete NOTAMs. 

3.

 

Put  the  Belfort  AWOS  in  “service  mode”  by  toggling  the  “ALERT  MESSAGE”  toggle 
switch located on the lower half of the hinged tower section six (6) times.  

4.

 

Remove  tower-securing  bolts  and  tilt  the  tower  until  the  cross  arm  is  at  a  comfortable 
working height to access the wind Speed sensor.  Secure the tower in that position by tying 
the  attached  tower  hold  down  rope  to  the  base  of  the  Belfort  AWOS  tower  as  shown  in 
Figure 2. 

5.

 

Perform  the  Temperature,  Humidity  Sensor  and  Dew  Point  Annual  Maintenance  and 
Verification procedure detailed in Section 5.3 of this manual. 

6.

 

If this  does not  return the unit to  service,  power  down the  power enclosure,  remove  and 
replace the sensor.   If no replacement sensor is immediately available, remove the  faulty 
sensor  from  the  system.  The  Temperature/Humidity/Dew  Point  will  be  reported  by  the 
system as ‘Not Available” until the replacement sensor is installed.   

7.

 

Power up the Power Enclosure. 

8.

 

Untie  the  rope  and  SLOWLY  erect  the  tower  to  the  vertical  position  and  secure  it  by 
installing and tighten-up (DO NOT OVER TIGHTEN) the three (3) tower-securing bolts.  
NOTE: Be careful to avoid pinching the wires on the inside of the hinged Tower Section 
when raising the tower. 

9.

 

If a system component has been determined to be faulty or suspect bad, go to Section 5.10 
and follow those instructions.   

10.

 

At the DATU display operator’s terminal, when all maintenance actions are complete, issue 

another  NOTAM  advising  users  that  “

Belfort  AWOS  maintenance  activities  were 

completed,  system  has  been  returned  to  normal  operation

.”  The expiration date and 

time of this NOTAM should coincide with the same expiration date and time of the previous 
advisory NOTAM that was issued to put the system in the maintenance mode.  Verify that 
this NOTAM advisory is correctly displayed on the operator screen.  Refer to the 

"Belfort 

AWOS Operator Manual"

 for instructions on how to enter and delete NOTAMs. 

 

 

Visibility Sensor, Sensor Error Counter Indicators  

Note:    The  Ambient  Light  Sensor  is  an  integrated  part  of  the  Visibility  Sensor.    If  the 
Visibility sensor is bad, the Ambient Light Sensor (ALS) may also be reported as bad.  If 
the Visibility Sensor is removed from service, the ALS must also be removed with it at the 
same time. 

 

1.

 

If  either  of  the  Visibility  Sensor  or  Visibility  Error  Counter  indicators  are  present,  the 
Visibility Sensor is bad or not responding to the DCP information polling request. 

2.

 

The  Visibility  Polling  Error  Counter  is  an  incidence  counter  of  Visibility  Sensor  non-
responses  to  polling  requests  from  the  DCP.    It  is  used  for  factory  remote  diagnostic 
assistance.  A factory technician may ask for the status or value of this indicator.  

3.

 

At the DATU display terminal,  issue a NOTAM advisory to  alert  users that  the  Belfort 
AWOS  system  is  being  serviced  prior  to  beginning  investigation  of  this  fault.    The 
NOTAM  to  be  issued  is 

"Belfort  AWOS  system  being  serviced,  do  not  use  current 

weather data outputs." 

Verify that this NOTAM advisory is displayed on the operator 

screen prior to beginning this maintenance tasks.  Refer to the "Belfort AWOS Operator 
Manual" for instructions on how to enter and delete NOTAMs. 

Содержание AWOS
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды