manualshive.com logo in svg

Belfort AWOS, Руководство по обслуживанию

Поделиться
Скачать
Belfort AWOS Скачать руководство пользователя страница 82

  

BELFORT

 

INSTRUMENT 

Proprietary Information

 

should be b13.5vdc and +14.0vdc.  If the voltage is within range, 
record the voltage on the Commissioning / Annual Record Data Sheet and 
go to the next Test step.  If the voltage is out of range, use a screwdriver to 
adjust the voltage on the power supply adjustment mechanism.  If the 
voltage will not adjust to within range, replace the power supply.   

 

d)

 

Battery Supply voltage.  Measure the Battery Supply voltage on the Battery 
connection terminals. The voltage should be b12vdc and +13.8vdc.  
If the voltage is within range, record the voltage on the Commissioning / 
Annual Record Data Sheet and go to the next Test step.   
If the voltage is below range, open the Battery Circuit Breaker.  Measure the 
DCP Trickle Charge voltage level on the output side (not the input from the 
battery) of the circuit breaker.  The voltage should be greater than 
>+12.2vdc.  If voltage level is less than +12.2vdc then the trickle charger is 
faulty in the DCP, and will need to be replaced.   If the voltage level is 
greater than +12.2vdc, then go to Test Step e. 

  

e)

 

Battery Fluid Levels.  Verify the fluid levels in the 6 battery cells.  If the 
fluid levels are correct, then record the information on the Commissioning / 
Annual Record Data Sheet and go to test Step f.  If any of the levels are 
incorrect, add water to the cell to the required level.   Record the 
information on the Commissioning / Annual Record Data Sheet and go to 
test Step f. 

 

 

f)

 

Close the Battery Circuit Breaker. 

 
IV.

 

Belfort AWOS DCP UHF Data Radio Accuracy Test: 

 

1)

 

Notify Regional OCC that system is being taken out of service if it is a 
commissioned system. 

 
2)

 

Lower the Tower.  Remove the DCP cover.  Record the serial number of the DCP 
Ritron Model DTX-454 RF Transceiver on the Commissioning / Annual Record 
Data Sheet. 

 
3)

 

Confirm that the HP8920B has been warming up for the minimum of ½ hour 
before use.  Select the TX function and then FM Demodulation on the HP8920B 
front panel. 

 

4)

 

Connect the DCP to the PC console and open a DOS window.  On the PC start the 
appropriate version of ACBSTXCOM program provided on the site notebook PC 
as follows: enter the DOS command “ACBSTXCOM comx” into the console 
starts the ACBSTXCOM program.  (Comx is the number of the communications 
port that you use for serial communications.)  Enter the “M” command at the “-“ 
prompt.  The “Enter Password” message will be displayed.  Enter the “Password”.  
Access will be granted to the built in hardware tests.  This stops all RF 
transmission via the DCP RF transceiver. 

 

Содержание AWOS
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды