manualshive.com logo in svg

Belfort AWOS, Руководство по обслуживанию

Поделиться
Скачать
Belfort AWOS Скачать руководство пользователя страница 35

-32- 

BELFORT

 

INSTRUMENT 

Proprietary Information

 

supply.   If no AC short  is found, then suspect the circuit breaker is  faulty.  Replace the 
circuit breaker. 

4.

 

Check inline fuses. If +14VDC is present and the inline fuse is OK, remove tower-securing 
bolts and tilt the tower until the cross arm is at a comfortable working height to access the 
wind Direction sensor.  Secure the tower in that position by tying the attached tower hold 
down rope to the base of the Belfort AWOS tower as shown in Figure 2. Put the Belfort 
AWOS in “service mode” by toggling the “ALERT MESSAGE” toggle switch located on 
the lower half of the hinged tower section six (6) times.  

5.

 

Loosen  the  4  screws  securing  the  DCP  to  the  tower  and  extend  the  DCP  so  the  cable 
attachments can be checked on the back of the DCP.  Make sure the 4 wire power cable is 
securely seated in the DCP.

    

If this does not return the AC power status indicator to service 

and the DCP continues to run on battery backup, remove the 4 wire power cable from the 
DCP.  Note that this removes all power from the DCP.  Measure the DC voltages across 
the 4 pins of the power cable as follows: 
 

Pin 1 + to 2- should m14.00 vdc from DCP power supply (PS) 
Pin 4 + to 3- should m12 vdc from the battery 

 

If the voltages are both present, then suspect the DCP AC status circuit is faulty. 
When convenient, the DCP should be sent to the factory for repair or replaced.  
If the PS DC voltage output is missing, then suspect a DC power supply failure, or loss of 
AC input voltage to the power supply, or a DC voltage conductor in the tower power cable 
is broken or shorted.  
If the AC voltage in missing, then suspect an open circuit breaker, AC wiring short, AC 
Mains supply feed is off. 
 

 

6.

 

If the Voltage to the AC monitoring circuit is restored, re-attach the DCP to the tower with 
it screws. 

7.

 

Untie  the  rope  and  SLOWLY  erect  the  tower  to  the  vertical  position  and  secure  it  by 
installing and tighten-up (DO NOT OVER TIGHTEN) the three (3) tower-securing bolts.  
NOTE: Be careful to avoid pinching the wires on the inside of the hinged Tower Section 
when raising the tower.  

8.

 

If  additional  maintenance  tasks  are  to  be  performed,  skip  to  next  maintenance  task.    If 
maintenance tasks are complete, toggle the “ALERT MESSAGE” switch 4 times to return 
he unit to service. 

9.

 

If a system component has been determined to be faulty or suspect bad, go to Section 5.10 
and  follow  those  instructions.    Else,  at  the  DATU  display  operator’s  terminal,  when  all 
maintenance  actions  are  complete,  issue  another  NOTAM  advising  users  that  “

Belfort 

AWOS

 

maintenance activities were completed, system has been returned to normal 

operation

.”  The expiration date and time of this NOTAM should coincide with the same 

expiration date and time of the previous advisory NOTAM that was issued to put the system 
in the maintenance mode.  Verify that this NOTAM advisory is correctly displayed on the 
operator screen.  Refer to the 

"Belfort AWOS Operator Manual"

 for instructions on how to 

enter and delete NOTAMs

.

 

 

Battery Condition – Error flag is present if AC power is off and backup battery is low.   
 

Содержание AWOS
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды