manualshive.com logo in svg

Baroness LM2700, Руководство по обслуживанию

Поделиться
Скачать
Baroness LM2700 Скачать руководство пользователя страница 145

1

Electro-magnetic check valve

2

Nipple

3

Elbow

4

Valve board

5

Bolt

6

Spring washer

Installation of Electro-Magnetic Check Valve

Caution

After the installation, check if there is no oil
leakage in each part.

Caution

See the list in "Tightening torques" (Page
3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

Important

Make sure of the installing locations of the
hydraulic pipes and do not install them at the
wrong locations.

For installation, reverse the removing
procedure.

Fuel Port Breather

Removal of Fuel Neck Breather

Remove the left tank cover. (See "Removal
of Left Tank Cover" (Page 7-39) .)

1.

Remove four round head screws, and then
remove the fuel neck breather from the
hydraulic tank.

2

3

1

3stwuh-002

Removal of Fuel Neck Breather_001

1

Hydraulic tank

2

Filler neck breather

3

Roundhead screw

Installation of Filler Neck Breather

Caution

After installation, check each part for oil
leakage.

Caution

See the list in "Tightening torques" (Page
3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

For installation, reverse the removing
procedure.

Orbitrol

Removal of Orbitrol

Remove the front cover. (See "Removal of
Front Cover" (Page 7-34) .)
Remove the front rear cover. (See
"Removal of Front Cover" (Page 7-34) .)

2.

1.

2.

Hy

draulic system

LM2700

Hydraulic system

Page 5-91

Removal and installation of each section

Содержание LM2700






































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды