B&R ACOPOSinverter P84, Руководство пользователя

Страница: 126 / 405

Programming guidelines
126 ACOPOSinverter P84 User's Manual 2.10
Other configurations and settings
Only in the "Hoist" macro configurations and "Mast./Slave" are additional parameters assigned outside the I/O
assignment.
Hoisting:
• [Movement type] (bSt) = [Hoisting] (UEr) , see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
• [Brake contact] (bCI) = [No] (nO) , see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
•
[Start pulse brake] (bCI) = [No] (nO) , see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
• [I Brake release upw.] (Ibr) = [Rated current motor] (nCr) , see "[BRAKE LOGIC CONTROL] (bLC-)" on
page 223
• [Brake release time]
(brt) = 0.5 s, see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
•
[Freq. brake release] (bIr) = [Auto] (AUtO) , see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
• [Freq. brake engage] (bEn) = [Auto] (AUtO) , see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
• [Brake engage time]
(bEt) = 0.5 s, see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
• [Engage at rev.] (bEd) = [No] (nO) , see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
• [Jump at reversal] (JdC) = [Auto] (AUtO) , see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
•
[Time to restart] (ttr) = 0 s, see "[BRAKE LOGIC CONTROL] (bLC-)" on page 223
• [Current ramp time] (brr) = 0 s, see "Overview of parameters for the brake logic (brH2 - brr)" on page 226
• [Low speed]
(LSP) = Motor slip calculated by inverter, see "Parameters that can be modified during oper-
ation or when the motor is stopped." on page 130
•
[Output Phase Loss] (OPL) = [Yes] (YES) , see "THERM. MOTOR PROTECTION (tHt) and LOSS OF
MOTOR PHASE (OPL)" on page 292 . No more changes can be made to this parameter.
• [TRAP WHEN RUNNING] (FLr) = [No] (nO) , see "CATCH ON THE FLY (FLr-)" on page 290 . No more
changes can be made to this parameter.
Mast./Slave:
•
[MOTOR CONTROL TYPE] (Ctt) = [SVC I] (CUC) , see "Drive parameters (Ctt)" on page 153
Note:
These assignments are forced for each change of the macro configuration, except
[Motor control type] (Ctt) for the case of in [FVC] (FUC) Mast./Slave configured macro configuration.
Reset to factory settings:
When resetting to factory settings with the command [Select config.] (Source config.) (FCSI) = [Macro conf] (InI), ,
see "Factory setting parameters (FCS1 - SCS1)" on page 315 the inverter is reset to the selected macro reset con-
figuration. The parameter [Macro config.] (CFG) does not change, however [Customer spec. macro] (CCFG) is
deleted.
Note:
The factory setting displayed in the parameter tables corresponds to [Macro config.] (CFG) = [Start/
Stop] (StS) . This is the factory-set macro configuration