B&R ACOPOSinverter P84, Руководство пользователя

Страница: 128 / 405

Programming guidelines
128 ACOPOSinverter P84 User's Manual 2.10
Overview of parameters [SIMPLE START] (SIM-)
Code Name/Description Setting range Factory settings
tCC [2/3 wire control] [2 wire control] (2C)
2C [2 wire control] (2C)
3C
[3 wire control]
(2C)
2 wire control: This is the input state (0 or 1) or edge (0 to 1 or 1 to 0), which controls running or stopping.
Example for wiring as "source":
Ll1: Forward
Llx: Reverse
3-wire control (edge-controlled): A "forward" or "reverse" pulse is sufficient for motor startup. A "stop" pulse is sufficient to stop the motor.
Example for wiring as "source":
Ll1: Stop
Ll2: Forward
Llx: Reverse
Warning!
ACCIDENTAL OPERATION OF DEVICE
To change the assignment of
[2/3 wire control] (tCC) , press down on the "ENT" key for 2 s. The following function is reset to
the factory settings: [Type 2 wire control] (tCt) , see "Input and output parameters (tCC - rr5)" on page 166 , as well as all the
functions that assign the logic inputs.
The selected macro configuration will also be reset if they contain customer-specific settings (loss of customer-specific settings).
Check that this change is compatible with the wiring diagram used.
Failure to follow these instructions will result in death or serious injury.
CFG [Macro configuration] [Start/Stop] (StS)
StS [Start/Stop] (StS) : Operating / Standstill
HdG [Mater.Handl] (HdG) : Conveyor technology
HSt [Hoist] (HSt) : Hoisting gear
GEn [Gen. Use] (GEn) : General applications
PId [PID CONTROLLER] (PId) : PID control
nEt [Buscom.] (nEt) : Communication bus
MSL [Mast./Slave] (MSL) : Master / Slave
Warning!
ACCIDENTAL OPERATION OF DEVICE
To change the assignment of
[Macro config.] (CFG) , press down on the "ENT" key for 2 s.
Check that the selected macro configuration is compatible with the wiring diagram used.
Failure to follow these instructions will result in death or serious injury.
CCFG [Customized macro]
Read-only parameter, only visible if at least one macro configuration parameter has been modified.
YES [Yes] (YES)
bFr [Standard mot. freq] [50 Hz IEC] (50)
50 [50 Hz IEC] (50) : IEC
60
[60 Hz NEMA]
(60) : NEMA
This parameter changes the default setting of the following parameters: [Rated motor voltage] (UnS) , [Size frequency] (HSP) ,
[F. thresh. Mot] (Ftd) , [Rated motor freq.] (FrS) , [Max. output freq.] (tFr) , [Rated motor current:] (nCr) , [Rated motor speed] (nSP) and
[Brake tightening power] (Ibr) .
IPL [Input phase fault] According to in-
verter performance
nO [Ign fault] (nO) : Fault ignored; to be used when the inverter is supplied via a single phase supply or by the DC bus.
YES
[freewheel stop]
(YES) : Fault with stop in freewheel stop.
At the loss of a phase the inverter goes into the fault mode [Line phase error] (IPL) . In case of a loss of 2 or 3 phases, the operation of the
inverter continues until the triggering of an undervoltage fault.
This parameter can be set in this menu only for inverters of type 8I84T200037.01P-1 to 8I84T200750.01P-1 (single-phase operation).
nPr [Rated motor power] According to in-
verter performance
According to in-
verter performance
Rated motor power in accordance with the nameplate in kW if [Standard Motorfreq.] (bFr) = [50 Hz IEC] (50) ; in HP, if [Standard Motorfreq.]
(bFr) =
[60 Hz NEMA]
(60) .