Bandit 200UC Скачать руководство пользователя страница 43

Страница: 43 / 110

Bandit

MODEL 200 UC

MAINTENANCE

EXPLANATIONS OF SPECIFIC

WEEKLY MAINTENANCE

WHEEL LUG NUTS

STEEL FRICTION AREAS

CHAIN DRIVEN COMPONENTS

Keep lug nuts tight, retorque, replace if needed.

Lubricate all steel friction areas including, but not

limited to pivoting, hinged, sliding, rotating areas on

the machine (i.e. stop bar, folding tray, discharge

flipper, hydraulic valves & linkages, height adjustable

discharge, discharge T-handle, etc.)

Use a dry lube on any chain driven components:

hydraulic swivel discharge and chain driven

feedwheels.

ALTERNATOR & FAN BELTS ON ENGINE

Inspect belt condition and replace as needed.

As applicable adjust and maintain per the engine

manufacturer’s manual.

EXPLANATIONS OF SPECIFIC

MONTHLY MAINTENANCE

CHIPPER BEARINGS & CHIPPER SHEAVE

HYDRAULIC FUNCTION PRESSURES

WHEEL BEARINGS

BRAKES

DISCHARGE CHAIN TENSION

TOWING HITCH

DISCHARGE & INFEED HOPPER WEAR

SHARPNESS OF FEEDWHEEL TEETH

Check, retighten all bearing bolts, bearing lock

collars, and also belt sheave bushings to correct

torques.

Check, reset and maintain all hydraulic function

pressure settings to a maximum of the specified

pressure. This will give you the best performance

from the hydraulic system.

Check and grease or oil wheel bearings per axle

manufacturer’s instructions.

Check and adjust brakes as needed per axle MFG.

manual.

Check tension on hand crank swivel discharge

chain drive and tighten as necessary. Chain tension

is 1/4” (6 mm) per foot (0.3 m) of center distance

between sprockets, NOT to exceed a 1/2” (13 mm)

of deflection. Do not overtighten.

Check for excessive damage or wear. Replace if

needed. Keep pintle ring greased to reduce wear.

Check for wear on discharge, infeed hopper,

and discharge direction adjuster; build up, repair or

replace as needed.

Replace if needed.

EXPLANATIONS OF

SPECIFIC 3 MONTH

MAINTENANCE

EXPLANATIONS OF

SPECIFIC YEARLY

MAINTENANCE

HYDRAULIC OIL FILTER(S)

HYDRAULIC OIL

HYDRAULIC SUCTION SCREEN(S)

FUEL TANK

Must be replaced after first 10 hours of operation,

use a 10 micron filter. After first change replace oil

filter every 3 months or 400 hours.

Change hydraulic oil and flush the hydraulic

reservoir tank.

Change hydraulic suction screen(s) yearly or

every 2000 hours.

Drain and clean the fuel tank yearly.

DISCHARGE SWIVEL PLATES

Grease swivel plates for discharge as needed.

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды