Bandit 200UC Скачать руководство пользователя страница 68

Страница: 68 / 110

1/21

MODEL 200 UC

HYDRAULICS

HYDRAULIC PRESSURE ADJUSTMENT

NO PRESSURE CHECK KIT

MAINTAIN FEEDWHEEL HYDRAULIC PRESSURE AT SPECIFIED PSI (bar).

Put the control bar in the off position.

2. Disconnect the autofeed block from the control

valve and plug the port on the autofeed block.

If your machine has only one feedwheel,

disconnect the hydraulic hose going from the

control valve to the feedwheel motor at the

feedwheel control valve end and plug the end

of the hose.

3. Leave all other hydraulic hoses connected.
4. Install pressure gauge in port on the control

valve from which the autofeed block or hose

was disconnected.

Start engine with the control bar in the off

position.

6. Adjust engine to full throttle.
7. Engage control bar to the normal operating

position to activate a reading on the pressure

gauge.

With the engine shut down, make sure the hydraulic oil is clean and the tank is 7/8 full. Start the engine

to allow the hydraulic oil to warm up. Before checking or adjusting the hydraulic pressure settings, make

sure the engine is shut off and the ignition key is in your possession. Ensure the pressure gauge is installed

correctly to check the relief valve pressure.

Pressure gauge should read maximum specified

PSI (bar).

ONLY ENGAGE CONTROL BAR FOR 4-5

SECONDS TO SET PRESSURE OR YOU

MAY DAMAGE HYDRAULICS.

9. Locate relief next to autofeed solenoid, loosen

jam nut, use an allen wrench to readjust relief

pressure setting if needed, and then retighten

jam nut.

10. Reassemble autofeed block or hose to control

valve.

11. Check for hydraulic leaks.
12. Relief valve pressure should be checked and/or

readjusted every month for best performance.

SAFETY INSTRUCTIONS

Allen

Wrench

Allen

Wrench

Main

Relief

Main

Relief

Main Relief Block

Feedwheel

Control

Valve

Insert Gauge

Into “B” Port

in Feedwheel

Control

Valve

Remove the hose from

“B” Port on

Feedwheel Control

Valve &

Plug the hose

Main

Relief

Block

Pump

Hydraulic

Tank

Main

Relief

Autofeed

Valve

Flow

Divider

Top

Feedwheel

Bottom

Feedwheel

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды