Bandit 200UC Скачать руководство пользователя страница 57

Страница: 57 / 110

Bandit

MODEL 200 UC

MAINTENANCE

CLUTCHLESS BELT TENSION

1. Before attempting any type of maintenance,

disengage clutch, wait for the disc to come to

a c omplete stop, turn off engine, remove the

ignition key, make sure the ignition key is in

your possession, install the disc lock pin, and

disconnect the battery.

2. The belt keeper must be adjusted to keep

the belt clear of the engine sheave while

disengaged. If the belt is not clear of the engine

sheave follow the instructions below.

3. Engage the tensioning system.

4. Loosen the bolts as shown in Figure 1.

5. Adjust the arm so that there is a clearance of

3/4” from the center of the belt keeper bolt to

the inside of the belt.

6. Retighten and retorque the bolts to 80 ft.-lbs

(108 Nm).

7. If replacing the belt; adjust the bottom beltshield

pan to remove the old belt and put the new belt in.

Readjust the pan to allow a 1/4” to 3/8” clearance.

ADJUSTING THE BELT KEEPER

FIGURE 1

To adjust the belt keeper, loosen these

bolts. Make sure to torque them after the

proper clearance is achieved.

Straight

Edge

Belt tensioner must be parallel with

the engine sheave and the chipper

sheave

CHIPPER

SHEAVE

BELT

TENSIONER

ENGINE

SHEAVE

FIGURE 3

FIGURE 2

CHIPPER

SHEAVE

ENGINE

SHEAVE

BELT

TENSIONER

IDLER

BELT

KEEPER

BELT

MUST HAVE A

CLEARANCE OF

APPROX. 3/4”

MUST HAVE A CLEARANCE

OF 1/4” - 3/8”

BOTTOM BELTSHIELD

PAN

NOTICE

Use a straight edge to make sure the belt tensioner

is properly aligned with the engine sheave and the

chipper sheave.

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды