Bandit 200UC Скачать руководство пользователя страница 53

Страница: 53 / 110

Bandit

MODEL 200 UC

MAINTENANCE

NOTICE

Clearances that are too small will result in excessive drag and overheating while

too much clearance can render the brake nonfunctional.

AXLE SIZE

SIZE

TYPE

DIAMETRAL CLEARANCE CLICKS TO BACK OFF

6,000 LBS.

12 1/2” x 2”

Elec. or Hyd.

.040” (1 mm)

14 to 24

7,000 LBS. 12 1/2” x 2.5” Elec. or Hyd.

.040” (1 mm)

7 to 13

TIRE MAINTENANCE

TIRE WEAR DIAGNOSTIC CHART

• Misalignment - from rough roads, pot holes,

excessive speeds and hitting curbs.

The wear pattern and tread life of tires involves many

variables that the user has control of, but does not

fall under faulty manufacture or design.

The following is a list of some causes supplied by

tire suppliers and axle manufacturers:

BASIC WHEEL TORQUE REQUIREMENTS (per mfg.)

Keep lug nuts properly tightened, check new unit before operation, after the fi rst 10, 25, and again

at 50 miles. Check the torque weekly.

DESCRIPTION

BOLT SIZE

TORQUE (FT.-LBS.) TORQUE (Nm)

5 & 6 Lug Hubs

1/2” - 20 Studs

90 - 120

122 - 163

8 Lug Hubs

1/2” - 20 Studs

90 - 120

122 - 163

8 Lug Hubs

9/16” - 18 Studs

140 - 170

149 - 163

8 Lug Hubs (Cone Nut)

5/8” - 18 Studs

190 - 210

258 - 285

8 Lug Hubs (Flange Nut)

5/8” - 18 Studs

275 - 325

373 - 441

8 Lug Hubs (Flange Nut)

22 mm x 1.5 Studs

450 - 500

610 - 678

10 Lug Hubs

22 mm x 1.5 Studs

450 - 500

610 - 678

10 Lug Hubs

3/4” - 16 Studs

450 - 500

610 - 678

10 Lug Hubs

1 1/8” - 16 Studs

450 - 500

610 - 678

(Consult axle manufacturers manual shipped with each machine for specifi c axle‑stud‑wheel combination

lug nut torques.)

Wear

Pattern

Edge Wear

Side Wear

Cup Wear

Center

Wear

Flat

Spots

Cause

Under

Infl ation

Not

hauling

trailer

level

Bent,

broken

or worn

axles

Wide tires

Wheel

bearings

Out of balance

wheel bearings

Over

infl ation

Wheel

lockup

and tire

lock up

Action

Adjust

pressure to

particular

load per

tire catalog

Must be

hauled

parallel

to the

ground

Replace

needed

Replace as

needed.

Characteristic

of wide

fl otation tires

Adjust or

replace

Check bearing

adjustment

and balance

tires. Adjust or

replace.

Adjust

pressure to

particular

load per

tire catalog

Avoid

sudden

stops and

adjust

brakes

•

Tire Width ‑ the wider the tire for fl otation, the more

uneven the tire wear.

• Tire Air Pressure - too much or too little, for the

load.

• Vehicle Hitch Height - if trailer is not level with

ground, axle camber is misaligned.

• Maintenance - wheel bearing lubrication and

adjustment. Follow axle manufacturer’s instructions.

• Brakes - uneven or misadjusted brakes cause

irregular brake activation.

Tighten the 5, 6, 8, and 10 lug hubs in sequence

according to the following diagrams.

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды