Bandit 200UC Скачать руководство пользователя страница 36

Страница: 36 / 110

1/21

MODEL 200 UC

OPERATION

OPTIONAL HYDRAULIC BUMP BAR OPERATION

The hydraulic bump bar is an optional device

which may help prevent accidents. Do not rely on

the hydraulic bump bar to prevent infeed accidents.

Never reach or kick into the infeed hopper for any

reason. Serious injury or death will result.

HYDRAULIC

BUMP BAR

HYDRAULIC

BUMP BAR

RESET

PUSH TO

ACTIVATE

MOMENTARY

FEED / REVERSE

• The optional Hydraulic Bump Bar comes set from

the factory and is non adjustable.

• If the Hydraulic Bump Bar is pushed, the

feedwheels stop.

• After the Hydraulic Bump Bar has been pushed,

the operator will need to reset it. Push the

Hydraulic Bump Bar Reset towards the tongue

of the machine. After the operator has done this,

the feedwheels will operate again.

• If there is wood or a branch that is pushing the

Hydraulic Bump Bar, the operator can push the

button shown above to momentarily operate the

feedwheels to reverse the wood back out. Then

the operator can reposition the wood or remove

the wood and cut the branch off before feeding

again.

DANGER

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды