Bandit 200UC Скачать руководство пользователя страница 33

Страница: 33 / 110

Bandit

MODEL 200 UC

OPERATION

MACHINE OPERATION

Butt end of

brush fi rst

Release limb or

log into chipper

Turn away from the

infeed hopper and keep

moving after releasing the

limb or log.

Travel

Path

Travel

Path

Figure 1

1. Once the machine is at full RPM, engage the

feedwheels in the forward direction.

2. Refer to feeding diagram (Figure 1).

A. Follow the travel path.

B. Feed only from the side of the infeed tray.

C. Release the limb or log.

D. Turn away and keep moving after releasing

the limb or log and from the infeed hopper.

3. Feed large, or butt end, of the branch or log into

the infeed hopper fi rst.

4. If the limb or log does not feed, it may need

repositioned. To reposition, read the following

steps:

A. Reverse the feedwheels, reposition

the limb or log, and feed again.

B. The log may need to be removed from the

machine to a safe work area and trimmed

before attempting to feed again if it still will

not feed.

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды