Bandit 200UC Скачать руководство пользователя страница 72

Страница: 72 / 110

1/21

MODEL 200 UC

HYDRAULICS

HYDRAULIC PUMP CHECK OUT

CORRECTING HYDRAULIC PROBLEMS

HYDRAULIC PUMP CHECK WITHOUT USING A FLOW METER

To check out the hydraulic pump the mechanic will need a needle type control valve, a pressure gauge

capable of reading 5000 psi (344 bar), an in-line 2500 psi (172 bar) relief, and a hose long enough to span

between the pump and the hydraulic tank.

1. Disconnect the pressure line going from the pump

at the fi rst component and cap the fi tting at the

component.

Attach a Tee fi tting to the end of the pressure

hose (which was removed from the component)

and install the Tee fi tting and gauge.

3. Attach an in-line 2500 psi (172 bar) relief to the

Tee fi tting with the gauge.

Attach the hydraulic fl ow control valve to the in‑line

relief and the hose (you supply) to the outlet port

of the fl ow control valve.

Make sure the pressure gauge is installed up

stream from the ﬂ ow control valve. Failure

to do this will cause serious damage to the

hydraulic pump when testing.

6. If the hydraulic oil tank is equipped with a mesh

strainer in the fi ll neck, remove it and place the

open end of the hose (you supply) into the tank

fi ll neck.

MAKE SURE THAT THE FLOW CONTROL

VALVE IS FULLY OPEN SO AS TO ALLOW

UNRESTRICTED FLOW TO PASS THROUGH

IT.

8. Start the engine to engage the pump, the clutch

may have to be engaged if the pump is belt

driven.

Do not exceed

90% of system

pressure.

First

component

after pump.

Hose

supplied by

you.

Flow

Direction

Hydraulic

Tank

Pump

Outlet

Flow

Direction

Tee

Fitting

Gauge

Flow Control

Valve

Cap after

removing

hose.

Remove any fi ller

neck screen.

In-Line

Relief

9. Have a second person lift the hydraulic hose far

enough out of the tank inlet to observe the fl ow

of oil going into the tank. Observe the pressure

gauge reading to make sure a high pressure

does not exist.

10. Increase the engine speed slowly to full rpm and

at the same time observe the pressure. This

should still remain low.

11.

SLOWLY

turn the needle valve on the flow

control in and observe the pressure increase on

the pressure gauge.

12.

Continue closing the fl ow control valve until the

pressure gauge reading reaches 90% of the

normal relief valve setting (example: if system

operates at 2500 psi (172 bar), do not exceed

2250 psi (155 bar).

Never allow the pressure to go more than 90%

of the main relief pressure.

13. If the pump is good there should be no noticeable

decrease in the fl ow rate coming out of the hose

and into the hydraulic tank.

14. If 90% of the main relief pressure can not be

obtained and/or the fl ow rate of the hose is

considerably less, then the pump is worn or

damaged.

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды