Bandit 200UC Скачать руководство пользователя страница 30

Страница: 30 / 110

1/21

MODEL 200 UC

OPERATION

This chipper hood engine disable plug is installed

for safety purposes. It is designed to shut down the

engine if the hood pin is not properly in place holding

the chipper hood in the closed position. The system

must be correctly maintained and operative at all

times. If the disable plug is not correctly installed

the engine will not start or run.

The patented Spring Lock for Hood Pin is installed

for safety purposes. It is designed to help keep the

hood pin from being removed if the chipper disc is

turning. Do not attempt to push the Spring Lock for

Hood Pin down or remove the hood pin until after

the engine and chipper disc both come to a complete

stop.
The spring lock is located on the side of the

chipper hood. The top of the spring lock should be

directly behind the hood pin washer when the hood

pin is properly installed in place holding the chipper

hood in the closed position (See Figure 1)
With the chipper hood shut and hood pin in place

the spring lock helps keep the hood pin from sliding

out or from being removed if the chipper disc is

turning. There is a shaft cam block installed on the

chipper shaft which will not allow the spring lock to

be pulled down if the chipper disc is turning (see

Figure 2). If the spring lock was to be pulled down

or recessed it would simply hit the shaft cam block

bouncing the spring lock back into position not

allowing for the removal of the hood pin.

The engine disable plug has a circuit fuse. If

the engine will not start or run, check the fuse fi rst

before consulting the engine manufacturer’s manual.

Circuit fuse locations: Caterpillar / Perkins - located

at the “BATT” wire near the ignition switch,

Cummins - located by engine manufacturer near the

starter (wires labeled “POW”), John Deere - located

by engine manufacturer “Short Stop” circuit breaker

by the ignition switch on the instrument panel or fuse

by the ECM, and Deutz, Hatz, Honda, Kohler, and

Robin - located at the battery post on the starter.

CHIPPER HOOD ENGINE DISABLE PLUG

SPRING LOCK FOR HOOD PIN

The chipper hood engine disable plug is wired

to shut down the chipper engine. When the disable

plug is pulled out of the electric socket the electric

circuit is broken, disabling the engine.

If the disable plug is not properly installed then

the engine will not start or run. If the disable plug

becomes disconnected while the chipper engine is

running the engine will be shut down or be disabled

from running. This is for safety purposes, to ensure

that the hood pin is not removed and the chipper

hood is not opened while the engine is running.

The chipper hood engine disable plug is located

on top of the chipper hood. The chipper hood engine

disable plug is made up of two parts: an electric

socket and a disable plug. The electric socket is

bolted to the chipper hood engine disable plug mount

bracket and the disable plug is attached by a cable

to the hood pin.

NOTICE

CABLE (TIGHT WHEN

PLUGGED IN AND

PADLOCK IS IN)

HOOD

ELECTRIC

SOCKET

PADLOCK

HOOD PIN

CHAIN

DISABLE

PLUG

CHIPPER

HOOD

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды