Bandit 200UC Скачать руководство пользователя страница 69

Страница: 69 / 110

Bandit

MODEL 200 UC

HYDRAULICS

With the engine shut down, make sure the hydraulic oil is clean and the tank is 7/8 full. Start the engine

to allow the hydraulic oil to warm up. Before checking or adjusting the hydraulic pressure settings, make

sure the engine is shut off and the ignition key is in your possession. Ensure the pressure gauge is installed

correctly to check the relief valve pressure.

Put the control bar in the off position.

2. Install pressure gauge on the test nipple that is

on the main relief.

3. Start engine with the control bar in the off

position.

4. Adjust engine to full throttle.
5. Close the ball valve.
6.

Pressure gauge should read maximum specified

PSI (bar).

ONLY CLOSE BALL VALVE FOR 4-5 SECONDS

TO SET PRESSURE OR YOU MAY DAMAGE

HYDRAULICS.

MAINTAIN FEEDWHEEL HYDRAULIC PRESSURE AT SPECIFIED PSI (bar).

HYDRAULIC PRESSURE ADJUSTMENT

PRESSURE CHECK KIT

7. Locate the relief on the main relief block, loosen

jam nut, use an allen wrench to readjust relief

pressure setting if needed, and then retighten

jam nut.

8. Remove the pressure gauge and place the

rubber cap back on the test nipple.

9. Check for hydraulic leaks.
10. Relief valve pressure should be checked and

readjusted as needed once a month for best

performance.

SAFETY INSTRUCTIONS

Feedwheel

Control

Valve

Ball Valve

Gauge

Main

Relief

Block

Pump

Hydraulic

Tank

Main

Relief

Allen

Wrench

Main

Relief

Autofeed

Valve

Flow

Divider

Top

Feedwheel

Bottom

Feedwheel

Main Relief Block

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды