Bandit 200UC Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 110

background image

Bandit

47

MODEL 200 UC

MAINTENANCE

MANUAL YOKE LIFT PROCEDURE

(FOR MACHINES WITHOUT HYDRAULIC YOKE LIFT)

1.  Follow all pre-maintenance shut down procedures.
2.  Make sure the machine hitch is securely coupled and locked to a tow vehicle.
3.  Remove the yoke springs.
4.  Remove the tongue jack and secure the jack to the yoke lifting mount as shown below. Must use a tongue

jack with a foot pad.

5. Crank the jack to raise the yoke and top wheel.
6.

Do Not rely on the hand jack to hold the yoke and top wheel up.

7.  Install the yoke lock pin completely and securely to help keep the top feedwheel in the raised position.
8.  Crank the jack to lower the yoke and top wheel so the weight is on the yoke lock pin and not the jack.
9.  Block and chain the top wheel up before doing any work inside throat
10. After the maintenance is complete, reverse the steps before putting the chipper back to work.

Slide Box Style Yoke

Pivot Style Yoke

Before attempting any type of maintenance,

disengage clutch, wait for the disc to come to a complete

stop, turn off engine, remove the ignition key, make

sure the ignition key is in your possession, install the

disc lock pin, and disconnect the battery.

SAFETY INSTRUCTIONS

«
...
59
60
61
62
63
...
»

Содержание 200UC















































































































Отзывы:

Нет отзывов

Похожие инструкции для 200UC

Бренд: GE Страницы: 802

Бренд: PageFlip Страницы: 32

Бренд: Farmet Страницы: 102

Бренд: EuroLite Страницы: 28

Бренд: Nel-Tech Labs Страницы: 8

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренд: Balanced Body Страницы: 37

Бренд: Yuwell Страницы: 2

Бренд: A.HABERKORN Страницы: 28

Бренд: Ultrasonic Страницы: 33

VLR100 LED Series

Бренд: WE-EF Страницы: 3

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Бренд: Conductix-Wampfler Страницы: 12

Flumen OPTI-TR 22

Бренд: Wilo Страницы: 88

Бренд: Electro-Music Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды