Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Страница: 23 / 110

Bandit
9
MODEL 200 UC SAFETY PROCEDURES
Chipper knives are sharp and can be dangerous.
It is always necessary for your protection to be
extra careful and wear proper hand protection when
handling knives.
WARNING
SAFETY PROCEDURES
Never turn the chipper disc by hand, always use
a pry bar or wood bar. Always rotate the chipper disc
backwards. Failure to do this could result in serious
injury.
Battery acid fumes are explosive. Never expose
an open fl ame or spark near the battery, keep all
burning materials away from the battery. When
servicing the battery, shield eyes and face, and do
not smoke; battery acid can cause severe burns.
Service in a well-ventilated area.
Do not go near hydraulic leaks. High pressure
oil easily punctures skin causing serious injury,
gangrene, or death. Avoid burns from fl uid. Hot
fl uid under pressure can cause severe burns. Do
not use fi ngers or skin to check for leaks. Lower
load or relieve hydraulic pressure before loosening
fi ttings. Relieve all pressure in the system before
disconnecting the lines, hoses, or performing other
work. Use a piece of cardboard to fi nd leaks. Never
use your bare hands. Allow system to cool down to
ambient temperature before opening any coolant or
hydraulic oil system.
The knives must be securely fastened and
torqued in position. If one comes loose or breaks
during operation, the machine will be damaged and
someone may get injured.
The machine was built with a chipper hood
engine disable plug which disables the engine if it
is not installed properly with the hood pin holding
the chipper hood in the closed position. Correctly
installed and maintained, the engine will not start
or it will shut off if the chipper hood engine disable
plug is disconnected. The chipper hood must never
be opened, or pushed closed if the chipper disc is
turning.
Before performing maintenance on the machine
remove all debris, oil, grease, water, snow, ice, etc.
from all machine surfaces.
Explosion hazard: Ultra low sulfur diesel (ULSD)
poses a greater static ignition hazard than earlier
diesel formulations with higher sulfur content.
Avoid death or serious injury from fi re or explosion;
consult with your fuel or fuel system supplier to
ensure the delivery system is in compliance with
fueling standards for proper grounding and bonding
practices.
Operation of this equipment may create sparks
that can start fi res around dry vegetation. A spark
arrester may be required. The operator should
contact local fi re agencies for laws or regulations
relating to fi re prevention requirements.
Never use jumper cables during freezing
temperatures. Tow the machine inside and allow
the battery time to warm up. If the machine must
be started outside, inspect the battery acid for ice
formation. Explosion will occur with a frozen battery.
If the machine is going to be operated in excessively
cold conditions, a larger cold cranking amp battery
may be needed to ensure proper and prompt
starting. Never use jumper cables in a confi ned or
unventilated area.
SAFETY INSTRUCTIONS
Before attempting any type of maintenance,
disengage clutch, wait for the disc to come to a complete
stop, turn off engine, remove the ignition key, make
sure the ignition key is in your possession, install the
disc lock pin, and disconnect the battery.
Always install the disc lock pin to prevent inadvertent
rotation. Insert the lock pin through the lock pin tube on
the belly band of the disc housing. This is to ensure the
chipper disc cannot be started while you are working
inside the machine. If, for some reason, the disc started
to turn, it would simply hit the lock pin.
To feed vine-like material, stop the feed system, cut
the vines or vine-like material into 4 to 5 ft. (1.2 to 1.5
m) lengths, in a clear area, away from the machine,
place them on the infeed tray, start the feed system,
and use the wooden pusher paddle to guide them
towards the feedwheel(s). Always be in position and
prepared to activate the feed control handle.
Before working inside the infeed hopper or under
the top feedwheel remove the yoke springs from the
top yoke, raise the yoke, install the yoke lock pin,
safety chain the yoke in the raised position, and insert
a wooden block to assist in holding the yoke in the
raised position. Failure to do this will cause serious
injury.