Bandit 200UC Скачать руководство пользователя страница 29

Страница: 29 / 110

Bandit

MODEL 200 UC

OPERATION

CONTROL OPERATING PROCEDURES

FEEDWHEEL TRAP DOOR

FEEDWHEEL CONTROL BAR

Before opening or closing the feedwheel trap door:

disengage clutch, wait for the disc to come to a complete

stop, turn off engine, remove the ignition key, make

sure the ignition key is in your possession, install the

disc lock pin, and disconnect the battery. In the event

that dirty material is being run through the chipper

the feedwheel trap door can be opened.

YOKE LIFT CONTROL (OPTIONAL)

The yoke lift control operates the top yoke lift

cylinder. To lower the yoke, push the yoke lift control

handle towards the discharge end of the machine.

To raise the yoke, push the yoke lift control handle

towards the infeed hopper of the machine. The yoke

lift control handle is in the flotation position when it

is in the center location.

SAFETY INSTRUCTIONS

The feedwheel control bar operates the

feedwheel(s). To make the feedwheel(s) operate

so they are pulling material into the machine, pull

the control handle towards the operator away from

the machine. To make the feedwheel(s) operate so

they are pushing material out of the machine, away

from the chipper disc, the control handle should be

pushed away from the operator, away from you and

towards the machine. The control bar is in the off

position when it is in the center location.

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды