Bandit 200UC Скачать руководство пользователя страница 44

Страница: 44 / 110

1/21

MODEL 200 UC

MAINTENANCE

Maintenance, along with proper operation, is the most important thing you can

do to get the optimum production and life out of the chipper. Failure to follow

proper maintenance procedures will aﬀ ect chipper life and void warranty!

TOP 10 CHIPPER MAINTENANCE ITEMS

Before attempting any type of maintenance, disengage clutch, wait for the disc to come to a complete

stop, turn off engine, remove the ignition key, make sure the ignition key is in your possession, install the

disc lock pin, and disconnect the battery.

SAFETY INSTRUCTIONS

MAINTENANCE

ITEM

WHAT TO CHECK

RESULTS

Knives & Anvil

Sharp knives - Bandit approved new

knives or professionally sharpened

Proper sharpening procedures will pay

dividends! Maintaining your chipper

knives will reduce fuel consumption and

increase the life of your chipper.

Proper knife width and angle
Properly torque the knife mounting

hardware.

Operating your chipper with dull knives

increases the amount of power required

to chip, increases machine vibration

and cause feeding problems. The extra

vibration will cause cracks to develop

throughout the machine and

void

warranty

Bandit approved knife mounting hardware,

must be replaced after 4 - 5 knife

rotations/changes to ensure safe clamping

ability

Correct anvil to knife clearance.

Anvil’s working edge is not rounded off or

chipped up.

Anvil hardware properly torqued.

Belt Drives

Belts must be tightened several times in

the fi rst few days of operation.

Loose and slipping belts will aff ect

the performance of feeding. Burnt,

glazed, and broke belts due to improper

adjustments

will not be

covered under

warranty

Proper belt tension.
Proper belt alignment.

Clutch

Adjust the clutch several times in the

break-in period per the manufacturer’s

manual.

If not adjusted correctly, the clutch

will slip under a load causing feeding

problems. Burnt and glazed clutches

will

not be

covered under warranty

DO NOT engage/disengage the clutch at

high rpm.

Do Not use the clutch to dislodge a jam.

Lubrication

All bearings, pivots points, hinges, chains,

etc. need to be greased or oiled per the

manual.

Improper lubrication will cause failure,

premature wear, or binding, which

will

not be covered under warranty

The feed system slide box must be oiled

to ensure proper operation, DO NOT

grease.

Engine

Maintenance

All fi lters, radiator screens, radiator,

coolant level, water separators, oil, etc.

must be checked, serviced, and changed

per the engine manufacturer’s manual.

Not following these maintenance

items will cause overheating, poor

performance, and could cause possible

engine damage that

will not be

covered

under warranty

Engine Radiators

& Screens

Clean the radiator with compressed air and/

or pressurized water (soap may also be

needed) to clean the radiator, depending on

the level and type of debris. If pressurized

water is used, be careful not to turn the

debris hard and pack solid between the

radiator fi ns.

Not following these maintenance

items will cause overheating, poor

performance, and could cause possible

engine damage that

will not be

covered

under warranty

Содержание 200UC















































































































Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды

Bandit 200UC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 200UC

Отзывы:

Похожие инструкции для 200UC

Бренды по названию

Популярные бренды