Baker Hughes Panametrics AquaTrans AT600 Скачать руководство пользователя страница 85

Страница: 85 / 174

AquaTrans™ AT600 User’s manual

Chapter 5. Error codes and troubleshooting

Chapter 5. Error codes and troubleshooting

5.1

Error display in the user interface

The bottom line of the LCD displays a single, top priority error message during operation. This line, called the error line,

includes two parts: error header and error string. The error header indicates the error pattern and error number, while

the error string gives a detailed description of the error information.

5.1.1

Error header

5.1.2

Flow error string

Flow errors are errors that occur during a flow measurement. These errors can be caused by disturbances in the fluid,

such as excessive particles in the flow stream or extreme temperature gradients. The errors could also be caused by

an empty pipe or other such issue. Flow errors are typically not caused by a malfunction of the flow measurement

device, but by a problem with the fluid itself or with the process piping.

Error pattern

Error header

Flow error

En (n is error number)

Device error

Dn (n is error number)

Warning

Sn (n is error number)

Option Bar

Description

Good

Bad

Tup

Displays the upstream ultrasonic signal transit time.

Tdn

Displays the downstream ultrasonic signal transit time.

DeltaT

Displays the transit time difference between the upstream and

downstream signals.

Up signal quality

Displays the signal quality for the upstream transducer.

≥1200

<400

Dn signal quality

Displays the signal quality for the downstream transducer.

≥1200

<400

Up amp disc

Displays the value for the signal amplitude of the upstream

transducer.

24±5

<19 or >29

Dn amp disc

Displays the value for the signal amplitude of the downstream

transducer.

24±5

<19 or >29

SNR up

Display the value for the signal-to-noise of the upstream signal. ≥4

SNR Dn

Display the value for the signal-to-noise of the downstream

signal.

≥4

Gain up

Display the value for the gain of the upstream transducer.

9-85

<9 or >85

Gain Dn

Display the value for the gain of the downstream transducer.

9-85

<9 or >85

Up peak

Displays the first value in the upstream correlation signal, which is

more than the positive threshold or is less than the negative

threshold.

Dn peak

Displays the first value in the downstream correlation signal,

which is more than the positive threshold or is less than the

negative threshold.

PeakPctUp

Displays the percentage of peak of the upstream signal.

PeakPctDn

Displays the percentage of peak of the downstream signal.

Содержание Panametrics AquaTrans AT600















































































































































































Результаты поиска

Содержание Panametrics AquaTrans AT600

Отзывы:

Похожие инструкции для Panametrics AquaTrans AT600

Бренды по названию

Популярные бренды

Baker Hughes Panametrics AquaTrans AT600, Руководство пользователя

Результаты поиска

Содержание Panametrics AquaTrans AT600

Отзывы:

Похожие инструкции для Panametrics AquaTrans AT600

Бренды по названию

Популярные бренды