Baker Hughes Panametrics AquaTrans AT600 Скачать руководство пользователя страница 27

Страница: 27 / 174

AquaTrans™ AT600 User’s manual

Chapter 2. Clamp-on fixture and transducer installation

2.3 Installing a general clamping fixture and transducer system

Both the C-RS and C-PT transducers are mounted on the pipe with the Panametrics general clamping fixture (GCF).

For detailed installation instructions refer to following:

• C-RS transducer installation Guide (Panametrics document #916-077)
• C-PT transducer installation Guide (Panametrics document #916-074)

2.3.1

Installing C-RS or C-PT transducers with an RG316 cable

The standard AT6 transducer cable is an RG316 cable with an SMA connector on the transducer end. To connect the

BNC connector on the C-RS or C-PT transducer to the SMA connector on the AT6 transducer cable, a BNC to SMA

adapter is needed. See figure 22 below and install the cable adapter on the transducer end of your AT6 cable.

Figure 22: BNC to SMA cable adapter installation

2.3.2 Installing C-RS or C-PT transducers with an RG62 cable

The AT600 flow meter can be connected directly to a C-RS or C-PT transducer with an optional RG62 cable, which has

a BNC connector at transducer end. Thus, the BNC to SMA adapter is not needed.
This RG62 cable has a submersible cable option for the C-RS transducer. Also, there is a junction box option for the

C-RS and C-PT transducers, which provides extra physical protection for the BNC connection on the transducer.

AT6 cable with SMA plug

BNC to SMA adapter

Transducer

with BNC Connector

Содержание Panametrics AquaTrans AT600















































































































































































Результаты поиска

Содержание Panametrics AquaTrans AT600

Отзывы:

Похожие инструкции для Panametrics AquaTrans AT600

Бренды по названию

Популярные бренды

Baker Hughes Panametrics AquaTrans AT600, Руководство пользователя

Результаты поиска

Содержание Panametrics AquaTrans AT600

Отзывы:

Похожие инструкции для Panametrics AquaTrans AT600

Бренды по названию

Популярные бренды