Baker Hughes Panametrics AquaTrans AT600 Скачать руководство пользователя страница 63

Страница: 63 / 174

AquaTrans™ AT600 User’s manual

Chapter 4. Initial setup and programming

4.6.4 Programming digital communications

The AT600 flow meter supports the following digital communication types:

• Modbus
• HART

A password is required to activate the digital communications options. In case of problems, contact Panametrics for

assistance.

4.6.4.1

Modbus

Selecting the baud rate

Selecting the Modbus address

To set up Modbus, select digital

comm on the input/ output screen

and press [√]. The following screen

opens.

Press [√] again, and a screen similar

to the following opens.

To set the baud rate, select baud

rate and press [√].
A screen similar to the following

opens.

The default baud rate is 115200. To

change the default, select the

desired baud rate and press [√] to

return to the previous screen.

To set the address, select Address

and press [√]. A screen similar to the

following opens.

Содержание Panametrics AquaTrans AT600















































































































































































Результаты поиска

Содержание Panametrics AquaTrans AT600

Отзывы:

Похожие инструкции для Panametrics AquaTrans AT600

Бренды по названию

Популярные бренды

Baker Hughes Panametrics AquaTrans AT600, Руководство пользователя

Результаты поиска

Содержание Panametrics AquaTrans AT600

Отзывы:

Похожие инструкции для Panametrics AquaTrans AT600

Бренды по названию

Популярные бренды