Bacharach 67-7622 Скачать руководство пользователя страница 66

Страница: 66 / 96

Page 4-12

Bacharach, Inc.

Instructions 67-9319

MAINTENANCE AND TROUBLESHOOTING

INJECTOR CALIBRATOR CD3

3. Open the hinged side door.

4. Remove the upper back panel.

5. Loosen the nuts holding the optical detector to

cross bar, and remove it from the cross bar.

6. Match mark the gear pump bracket and the

motor mounting plate.

7. Remove two bolts which secure the gear pump

bracket to the plate.

8. Slide the pump assembly off the end of the motor

shaft.

9. Insert the barring tool into the roller link assem-

bly and exert downward pressure raising the

motor. Leave the motor in the raised position.

10. Slip the new belt through the openings thus

provided and over the large diameter pulley on

top and the small diameter pulley below.

11. Reassemble the optical detector on the cross bar,

being careful to align it as per Section 4.3.4.

12. Reassemble the gear pump to the end of the

motor shaft.

13. Lower the motor to its original position.

14. Adjust the motor mounting plate spring tension

for 3-3/4 inches.

15. If required, slide the motor block shim (marked

CUM) under the leveler.

16. Lower or raise the leveler by hand until it just

contacts the shim.

17. Then lower the leveler one more turn and lock it

with the lock nut.

18. Check that the belt is now snug but not too taut.

19. Close the pulley cover.

20. Switch on the On/Off Switch.

Figure 4-20. Drive Belt (Top)

Figure 4-21. Drive Belt (Bottom)

5 Encoder wheel

5 Camshaft

8 Gear pump

Pulley

7 Gear pump bracket

Roller link

Содержание 67-7622

































































































Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды

Bacharach 67-7622, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды