Bacharach 67-7622 Скачать руководство пользователя страница 21

Страница: 21 / 96

Instructions 67-9319

Bacharach, Inc.

Page 2-3

INJECTOR CALIBRATOR CD3

INSTALLATION

Figure 2-6. Air Connection

Figure 2-7. Adjust Air Pressure

Figure 2-8. Calibration Drains

Air

8. Connect an air line from the shop supply (95 to

125 psi) to the fitting at the rear of the calibra-

tor marked AIR (1/4 inch NPT).

9. Check regulator settings. The Primary Air

Pressure Regulator should be set at 90 ± 5 psi,

the Secondary Air Pressure Regulator must be

set at 60 +5 -0 psi (4.1 bar). The regulators are

behind the lower rear panel.

CAUTION:

HIGH PRESSURE CAN DAMAGE AIR

REGULATORS. Shop air supply must not

exceed 125 psi.

10. For regulator adjustments see Section 4.3.2

2.4 Filling Reservoirs

Calibration Fluid

1. Check that both drains of the calibration fluid

reservoir are closed.

2. Through the dipstick port, fill reservoir to the

“F” mark on the dipstick with new fluid. Use

Bacharach part number 67-5598 (SAE J967).

3. After a few minutes, check for leaks.

4. Place a tag on the reservoir giving date it was

filled.

Cambox

The cambox is filled with lube oil at the factory.

However, if filling is necessary:

5. Make sure cambox drain plug is in place. Drain

plug is accessible after left-hand cab inlet door

is open.

6. Fill the cambox with SAE 30W motor oil to

bring the level up to within 3-3/4 inch from the

top (or about 1-1/2 inch from the bottom).

Intensifier

7. The intensifier reservoir is filled at the factory

before shipping. If additional fluid is required,

see Section 2.6.

Lift Red Ring

9 Check Regulator Setting

8 Air in

9 Adjust Primary Air Pressure
to 90 psi

9 Adjust Secondary Air Pressure to 60 psi

1 Close Both Drains

Содержание 67-7622

































































































Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды

Bacharach 67-7622, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды