Bacharach 67-7622 Скачать руководство пользователя страница 37

Страница: 37 / 96

Instructions 67-9319

Bacharach, Inc.

Page 3-11

INJECTOR CALIBRATOR CD3

OPERATION

Figure 3-23. Flanged Injector Accessories

Figure 3-24. Injector Setup

Figure 3-25. Setting Flywheel

3.1.7 Mounting Cummins Flanged Injectors

Before mounting injectors, check cambox to be sure

that the proper cam for the injector to be tested is

mounted on the camshaft. (See Section 3.1.3)

Also make sure the Cummins discharge head has

been installed. (See Section 3.1.4)

3.1.7.1 Inserting Injectors

1. Insert the injector into adapter H-NH, J-C (67-

6368) so that the flanged body holes slip over

the two pins.

2. Align the injector so that the injector outlet and

inlet ports face the operator and the slots in the

adapter face down.

3. Select the correct link and insert it into the

plunger.

Injector

Part No.

Ident.

Flanged, H-NH

67-6575

H-NH

Flanged, J-C

67-6576

J-C

4. Hold these parts in two hands and lower them

into the carrier plate, making sure that:

a. The adapter slot aligns with the protruding

3/8 in. pin.

b. The adapter rests against the semicircular

area of the carrier plate.

c. The link rests on top of the push rod exten-

sion.

3.1.7.2 Clamping Body to Seat

5. Lift the pulley cover to expose the camshaft

pulleys and flywheel.

6. Rotate flywheel by hand until the white painted

area on the flywheel shows through the window

(barring tool inserted in a hole in the flywheel

can help in turning the flywheel).

7. Close the pulley cover. Cover must be closed for

the main drive motor to operate.

8. To clamp the injector, press and hold down the

HOLD TO OPERATE button

Plunger
and Spring

Flanged
Injector

Link

Aapter

Push Rod Extension

4 Push Rod

4 Carrier Plate

1 Flanged Injector

4 Link

1 Adapter

2 Ports

6 White Painted Area On Flywheel

Содержание 67-7622

































































































Результаты поиска

Содержание 67-7622

Отзывы:

Бренды по названию

Популярные бренды

Bacharach 67-7622, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 67-7622

Отзывы:

Бренды по названию

Популярные бренды