Bacharach 67-7622 Скачать руководство пользователя страница 45

Страница: 45 / 96

Instructions 67-9319

Bacharach, Inc.

Page 3-19

INJECTOR CALIBRATOR CD3

OPERATION

Figure 3-40. Body to Seat Clamp

Figure 3-41. Injector Setup

3.2.4.3 Body to Seat Clamp

NOTE:

The body-to-seat air clamping is

not needed for DD injectors. To keep them

out of the way, activate the air cylinders

and leave them in clamped position during

the test.

5. Lift the pulley cover to expose the camshaft

pulleys and flywheel.

6. Rotate flywheel by hand (barring tool inserted

in holes in the flywheel can help in turning the

flywheel) until the white painted area on the

flywheel shows through the window.

7. Close the pulley cover. Cover must be closed for

the main drive motor to operate.

8. To clamp the injector, press and hold down the

HOLD TO OPERATE button

9. Press the BODY TO SEAT CLAMP button.

The air cylinders will retract and clamp injector.

10. Release the BODY TO SEAT CLAMP button

when the BODY TO SEAT monitor turns green.

3.2.4.4 Tubing

11. Push one end of the two-foot plastic tubing over

the fill tube (67-5292) and the other end over

the barbed elbow at the OUTLET port on the

manifold.

The plastic tubing and fill tube are part of the

calibrator accessories.

12. Insert fill tube into the drain tray center hole.

3.2.4.5 Injector

13. Slip the front support (67-6606) over the rails

approximately midway between the manifold

block and the injector carrier plate.

14. Place the injector in position so the lower body

rests on top of the semicircular front support

and the fuel connectors are aligned with their

ports in the manifold block.

9 BODY TO SEAT CLAMP

8 HOLD TO OPERATE

Manifold Inlet

Tubing

Swing Back Fuel Arm

Front Support

Injector

Содержание 67-7622

































































































Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды

Bacharach 67-7622, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды