Bacharach 67-7622 Скачать руководство пользователя страница 60

Страница: 60 / 96

Page 4-6

Bacharach, Inc.

Instructions 67-9319

MAINTENANCE AND TROUBLESHOOTING

INJECTOR CALIBRATOR CD3

4.2.2 Hydraulic System

Checking Hydraulic Pressure

To make sure that sufficient hydraulic pressure is

applied to the hydraulic cylinder locking sleeve:

1. Install a 0 to 5000 psi gauge at the upper port of

the hydraulic cylinder.

2. When holding the HOLD TO OPERATE button,

check the pressure reading. Pressure must be

3700 - 4500 psi.

3. If pressure is less than 3700 psi, check for air and

hydraulic leaks between the hydraulic pump and

the cylinder. Make sure that the secondary air

pressure supply is 60 - 65 PSI.

4. Remove the gauge installed in step 1.

Bleeding Air from System

4. Add oil to intensifier reservoir, if necessary, (see

Section 4).

NOTE:

Gauge port is the same as bleed port

for locking circuit.

5. Use 3/16 inch hex to “crack” plug at gauge port.

6. Press and hold the “HOLD TO OPERATE” button

and let some fluid flow past the loosened plug.

7. Allow air to escape through port until oil flows

freely.

8. While oil flows, tighten plug. Release the button.

9. Replenish oil in the reservoir immediately after

bleeding.

TROUBLESHOOTING CHART FOR ELECTRICAL PROBLEMS (cont.)

Fault

Possible Cause and Remedy

_________________________________________________________________________________

Flowmeter displays 1. Connector to main P.C. board may be loose – Reconnect.

all zeros; will not

2. Flowmeter limit switches may be tripped – Remove power and reposition piston

display flow

adapter block to center of cavity.

readings*

3. Detector #1 on flowmeter transducer may be defective – Replace.

4. Solenoid L8 may be defective – Replace.

________________________________________________________________________________

* If troubles with the flowmeter and main printed circuit board prove difficult to isolate, follow the isolation

procedure listed in Section 4.2.6.

** When replacing a printed circuit board, replace both the main printed circuit board and the display board.

Figure 4-9. Checking Hydraulic Pressure

1 Install pressure

gauge here

5 Bleed port

Содержание 67-7622

































































































Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды

Bacharach 67-7622, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды