manualshive.com logo in svg

Bacharach 67-7622, Инструкция по установке и эксплуатации

Поделиться
Скачать
Bacharach 67-7622 Скачать руководство пользователя страница 44

Page 3-18

  

Bacharach, Inc.

         Instructions 67-9319

OPERATION

     INJECTOR CALIBRATOR CD3

Figure 38. DD Type 53, 71, 92 & 92M

Accessories

Figure 3-39. Accessory Setup

3.2.4 Mounting DD Injector Types 53, 71, 92

and 92 Marine (92M)

Before mounting injectors, check cambox to be sure

that cam 77-0610 (53, 71, 92, 92 Marine, or 8.2 L) is

mounted on the camshaft.

The drain fitting for the manifold block assembly

(77-0613) can be positioned in either of two return

ports, depending on whether the injector to be

tested is offset or standard. As supplied by

Bacharach, the barbed elbow drain fitting is in

position for offset injectors. For standard injectors,

install the fitting in the other port.

The manifold block also includes three sets of

standoffs: The long standoffs are for low crab

injectors, the medium standoffs are for 92 Marine

injectors, and the short standoffs are for high crab

injectors.

3.2.4.1 Manifold

1. Slide the manifold block assembly (77-0613)

over the dowel pins, with the inlet port face up.

The return port with the barbed elbow should

be on the far side in a horizontal position.

2. Install correct standoffs in the manifold block.

Long standoffs:

Low crab injectors

Medium standoffs: 92 Marine injectors

Short standoffs:

High crab injectors

3.2.4.2 Discharge Head

3. Insert the discharge head for 53, 71, 92, & 92M

injectors (67-5696) into the clamp cylinder

socket with the quick connect socket set for

easy hose connection.

NOTE:

  When discharge heads are in-

stalled for the first time, wet O-ring with

calibration fluid for easier installation.

4. Insert the flowmeter tubing with the quick

connect plug into the discharge head socket.

Manifold
Block

Drain
Fitting

Standoffs

Front
Support

Discharge
Head

Injector

Alternate
Drain Port

4  Flowmeter Tubing

3  Discharge Head

Содержание 67-7622

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды