Bacharach 67-7622 Скачать руководство пользователя страница 34

Страница: 34 / 96

Page 3-8

Bacharach, Inc.

Instructions 67-9319

OPERATION

INJECTOR CALIBRATOR CD3

3.1.6 Mounting Cummins Types PTB and

PTC Cylindrical Injectors

Before mounting injectors, check cambox to be sure

that the proper cam for the injector to be tested is

mounted on the camshaft. (See Section 3.1.3)

Also make sure the Cummins discharge head has

been installed. (See Section 3.1.4)

3.1.6.1 Inserting Injectors

1. Pull out the plunger and spring from the

injector.

2. Insert the injector into the correct PTB or PTC

adapter.

Adapter

Injector

Part No.

Ident.

PTB, PTC 3/8

67-6604

3/8 PTB-PTC

PTB, PTC 5/16

67-6602

5/16 PTB-PTC

PTC 5/16 large

67-6602

5/16 PTB-PTC

radius link

3. Align the injector with the socket screw head in

the adapter.

4. Reinstall the plunger with the spring into the

injector from the opposite end of the adapter.

5. Insert the PTB-C or the PTC lg. rad. link into

the plunger.

6. Hold these parts in two hands and lower them

into the carrier plate, making sure that:

a. The adapter slot aligns with the protruding

3/8 in. pin.

b. The adapter rests against the semicircular

area of the carrier plate.

c. The link rests on top of the push rod exten-

sion.

Figure 3-16. PTB & PTC Accessories

Figure 3-17. Injector Setup

Figure 3-18. Setting Flywheel

1 Plunger and Spring

1 PTB (or PTC) Injector

Link

2 Adapter

5 Link

2 Adapter

6 Push Rod Extention

PTB, PTC Injector

6 Carrier Plate

8 White Painted Area On Flywheel

Содержание 67-7622

































































































Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды

Bacharach 67-7622, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды