Bacharach 67-7622 Скачать руководство пользователя страница 50

Страница: 50 / 96

Page 3-24

Bacharach, Inc.

Instructions 67-9319

OPERATION

INJECTOR CALIBRATOR CD3

Figure 3-53. Injector Setup

Figure 3-54. Injector Clamping

8. Press the BODY TO SEAT CLAMP button.

The air cylinders will retract and clamp injector.

3.2.6.4 Injector

10. Install the injector into the injector holder by

hand pushing until the mounting slots on both

the injector and the holder are aligned.

11. Then secure with the key, straight edge to-

wards the injector.

This will prevent the injector from moving out

during testing.

12. Place the injector holder with the injector over

the carriage rails.

3.2.6.5 Fuel Inlet

13. Disconnect inlet hose from quick disconnect at

the fuel inlet arm and push into the quick

connect at the top of the injector holder.

14. Attach the flexible plastic tubing to the barbed

elbow at the bottom of the injector holder.

15. Insert the other end of the tubing into the hole

of the drain pan.

3.2.6.6 Injector Clamping

16. Push and hold the HOLD TO OPERATE button

with left hand.

17. While holding down the HOLD TO OPERATE

button, move the CLAMP/UNCLAMP lever to

the CLAMP position with right hand.

Maximum clamping force shown on the CLAMP

MONITOR/TIMING PLUNGER TO BODY gauge

will be in the green segment of the dial and the

PLUNGER TO BODY timing light will be lit.

18. Wait until the PLUNGER TO BODY timing

light goes out (after about 3 seconds).

19. Release the HOLD TO OPERATE button

first

and

then

the CLAMP/UNCLAMP lever. The

lever will return to the center position.

For clamping to occur correctly, you must follow

this sequence carefully.

Injector 8.2

Key

Injector holder

Carriage rail

CLAMP

HOLD TO OPERATE

Содержание 67-7622

































































































Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды

Bacharach 67-7622, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 67-7622

Отзывы:

Похожие инструкции для 67-7622

Бренды по названию

Популярные бренды