Bacharach 67-7622 Скачать руководство пользователя страница 41

Страница: 41 / 96

Instructions 67-9319

Bacharach, Inc.

Page 3-15

INJECTOR CALIBRATOR CD3

OPERATION

3.2 Detroit Diesel (DD) Injectors

Cummins 189 cam (67-6370) is installed in the

cambox at the factory.

A complete set of DD accessories is supplied under

part number 67-7632 (Figure 5-15). The inside left

front door of the calibrator has spaces designated

for hanging DD accessories (Figure 3-32). Not all of

the DD accessories are shown in this photo. Hooks

are provided with the accessories.

DD Injectors are clamped against a manifold or

spacer between the injector and cambox. Supports

are required for the front of the injector. On DD 149

injector, a push rod extension is used between the

push rod and the injector follower. The 8.2 liter

injector needs a special holder assembly.

3.2.1 Quick Reference Charts for Testing

Injectors

This chart is for reference only. Use the procedures

on the following pages for preparing the calibrator,

accessories, and injectors for testing.

For testing all DD injectors the camshaft speed

must be 2000 RPM. To change speed see Section

3.2.2. For DD injectors, rail pressure must be 35

psi.

3.2.2 Changing Speed

The CD3 calibrator is shipped with the drive belt

disengaged. To change the speed setting to test DD

injectors:

1. Open the flywheel (sheave) cover to expose the

upper pulleys.

Figure 3-32. DD Injector Accessories

Detroit Diesel Accessory Part Number or Identification

_________________________________________________________________________________________________

Injector

Manifold

Front

Holder

Discharge

Push Rod Fuel

Injector

Block

Support

Assembly

Head

Cam

Extension Connector

--------------------------------------------------------------------------------------------------------------------------------------------------

53, 71, 92

77-0613

67-6606

——

67-5696

77-0610

——

92 Marine

77-0613

77-0913

——

67-5696

77-0610 77-0912

77-0866

149

67-7643

67-6605

——

67-5700

67-6372 67-5708

——

8.2 liter

——

67-8525*

67-5696

77-0610

——

—————————————————————————————————————————————————

(—— means the accessory is not needed)

*8.2 liter Injector Holder Set consists of a Spacer Block (67-6851), two Angle Spacers (67-6850), Injector Holder
(67-6854), with key, and Mounting Instructions (67-9388).

Figure 3-33. Detroit Diesel Injector Accessories Chart

Front
Supports

Manifold
Blocks

Cams

Spacer
Block

Pushrod
Extention

Discharge
Head

Injector
Supports

Discharge
Head

Angle
Spacers

Injector
Holder

Содержание 67-7622

































































































Результаты поиска

Содержание 67-7622

Отзывы:

Бренды по названию

Популярные бренды

Bacharach 67-7622, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 67-7622

Отзывы:

Бренды по названию

Популярные бренды