Avital AviStar 3300 страница 28 Скачать руководство пользователя | Manualshive

Страница: 28 / 50

background image

28

© 2000 Directed Electronics, Inc. Vista, CA

Type E door locks are controlled by an electrically activated vacuum pump. Some Mercedes and Audis use a Type

D system. Test by locking doors from the passenger key cylinder. If all the doors lock, the vehicle's door lock

system can be controlled with just two relays or a DEI

451M

. The control wire can be found in either kick panel

and will show (+)12V when doors are unlocked and (-) ground when doors are locked.

To interface see diagram below. The system must be programmed for 3.5 second door lock pulses. (See

Operation-

Settings Learn Routine™

section of this guide.)

This system usually requires a negative pulse to unlock, and cutting the wire to lock the door. In some vehicles,

these are reversed. It is found in late-model Nissan Sentras, some Nissan 240SX, and Nissan 300ZX 1992-up. It

is also found in some Mazda MPV's and some Mitsubishi's.

One relay (optional) is used to interface to this type of system as follows:

type F: one-wire system

type E: mercedes-benz and audi (1985 & newer)

«
...
26
27
28
29
30
...
»

Содержание AviStar 3300



















































Отзывы:

Нет отзывов

Похожие инструкции для AviStar 3300

vesda LaserFOCUS VLF-500

Бренд: Xtralis Страницы: 2

Бренд: Marquant Страницы: 31

Бренд: FIBARO Страницы: 14

Бренд: NATURE & DECOUVERTES Страницы: 9

Бренд: AVS Страницы: 4

Бренд: AVS Страницы: 12

Бренд: AUTHOR Alarm Страницы: 12

Бренд: HomeMatic Страницы: 65

Бренд: Sharper Image Страницы: 20

Бренд: iHome Страницы: 16

Бренд: iHome Страницы: 20

Бренд: SPAL Страницы: 2

Бренд: DEI Страницы: 40

Бренд: Code Alarm Страницы: 8

Бренд: Code Alarm Страницы: 18

Бренд: Directed Electronics Страницы: 20

Бренд: SenTech Страницы: 2

Бренд: SafeMi Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды