Avital AviStar 3300 Скачать руководство пользователя | Manualshive

Страница: 23 / 50

background image

© 2000 Directed Electronics, Inc. Vista, CA

23

shock sensor harness, 4-pin connector

Inputs shorter than 0.8 seconds will trigger the Warn Away response, while inputs longer than 0.8 seconds will

trigger full alarm sequence and report Zone Two. If installing an optional DEI dual stage sensor, connect to the

green wire as shown in the following. Following the wiring outlined in the diagram below eliminates the need

for diodes to isolate the sensors.

Diagram for adding optional DEI dual stage sensor to green wire (Zone 2):

Inputs shorter than 0.8 seconds will trigger the Warn Away® response, while inputs longer than 0.8 seconds will

trigger full alarm sequence and will also report Zone Two.

Do not use these wires for anything except the plug-in shock sensor.

RED and BLACK: RED is (+)12V constant, BLACK is (-) ground

BLUE (-) multiplex input, zone 2

GREEN (-) multiplex input, zone 2

«
...
21
22
23
24
25
...
»

Содержание AviStar 3300



















































Отзывы:

Нет отзывов

Похожие инструкции для AviStar 3300

Бренд: Velleman Страницы: 48

Бренд: FireBrand Страницы: 2

Бренд: Galeria Selection Страницы: 10

LIFESAVER silhouette 5800ACF

Бренд: PSA Products Страницы: 2

Бренд: Trevi Страницы: 20

Бренд: G-project Страницы: 20

Бренд: First Alert Страницы: 2

Бренд: First Alert Страницы: 1

Бренд: First Alert Страницы: 6

Бренд: First Alert Страницы: 7

Бренд: Firex Страницы: 6

Virtual Key 2UK

Бренд: Clifford Страницы: 8

Бренд: Clifford Страницы: 9

Бренд: Clifford Страницы: 15

Бренд: Clifford Страницы: 13

Бренд: Clifford Страницы: 28

Бренд: EVERSPRING Страницы: 13

Бренд: Vision Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды