Avital AviStar 3300 Скачать руководство пользователя

Страница: 44 / 50

valet mode

To enter or exit valet mode with the valet/program switch:

Turn the ignition key on and then off.

At any time during the next 10 seconds, press and release the Valet switch. Now the Status

LED will light constantly if you have entered Valet Mode or go out if you have exited Valet

Mode.

To enter or exit valet mode with the transmitter:

To enter or exit Valet® Mode with a transmitter:

1. Open any door.

2. Press

on the transmitter.

3. Press .

4. Press

again. You have now entered or exited Valet Mode (verify by checking your status LED).

timer mode

This unit can be programmed to start and run the engine every three hours, for a maximum of six cycles. The

engine will run for the programmed run time and then shut down. After three hours, the system will restart the

engine.

IMPORTANT!

Timer Mode should be used only in open areas. Never start and run the vehicle in an

enclosed space such as a garage or carport.

To enter or exit timer mode with the transmitter:

The same procedure may be used to enter or exit Timer Mode using the remote transmitter:

1. Remote start the vehicle.

2. Press and release the transmitter button(s) controlling Channel Two.

3. Press and release the transmitter button(s) controlling remote start operation.

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды