Avital AviStar 3300 Скачать руководство пользователя

Страница: 16 / 50

remote start secondary harness (H3) wire
connection guide

This wire supplies a 200mA output as soon as the module begins the remote start process. It can be used to

control an immobilizer bypass module for vehicles with factory immobilizers. The H3/1 BLUE wire can also be

used to rearm a factory anti-theft system when the remote start shuts down. (See the

Feature Descriptions

section

of this guide.)

This output provides a 200mA output as soon as the remote starter is activated. It can be used to power a relay to

energize a positive (+) third ignition as shown below. This output is capable of driving two relays if necessary.

This wire MUST be connected to hood pinswitch. This input will disable or shut down the remote start when the hood

is opened. It will also trigger the security system if the hood is opened while the system is armed and report Zone 1.

This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows (+) 12V when the brake

pedal is depressed. The remote start will be disabled or shut down any time the brake pedal is depressed. This

wire will also trigger the security system if the brake pedal is pressed while the system is armed and will report

Zone 1.

This input provides the module with information about the engine's revolutions per minute (RPMs). It can be con-

nected to the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy ignition

H3/5 VIOLET/WHITE tachometer input

H3/4 BROWN (+) brake switch input, zone 1

H3/3 GRAY (-) hood pinswitch input, zone 1

H3/2 BLUE/BLACK (-) optional third ignition output

H3/1 BLUE (-) status/factory re-arm output

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды