Avital AviStar 3300 страница 39 Скачать руководство пользователя

Страница: 39 / 50

feature descriptions

The features of this system are described below. Features indicated with the following icon have additional set-

tings that can be programmed when using the PC interface or Bitwriter:

1-1 ACTIVE/PASSIVE ARMING:

When active arming is selected, the system will only arm when the transmitter

is used. When set to passive, the system will arm automatically 30 seconds after the last door is closed. To alert

the consumer of passive arming, the siren will chirp 20 seconds after the door is closed. This provides the con-

sumer with an audible warning prior to the system actually arming. At the 30 second mark, the system will arm,

but the siren will not chirp.

1-2 CHIRPS ON/OFF:

This feature controls the chirps that confirm the arming and disarming of the system.

1-3 IGNITION CONTROLLED DOOR LOCKS ON/OFF:

When turned on, the doors will lock three seconds after

the ignition is turned on and unlock when the ignition is turned off. The TechSoft Programmer or the

998T

Bitwriter will display separate steps for ignition lock and unlock, which can be programmed on or off independently.

1-4 ACTIVE/PASSIVE LOCKING:

If passive arming is selected in Feature 1-1, then the system can be programmed

to either lock the doors when passive arming occurs, or only lock the doors when the system is armed via the

transmitter. Active locking means the system will not lock the doors when it passively arms. Passive locking

means that the system will lock the doors when it passively arms.

menu #1 - basic features

FEATURE

ONE-CHIRP SETTING (DEFAULT)

TWO-CHIRP SETTING

3-1

Engine checking on

Engine checking OFF

3-2

Engine checking TACH

Engine checking VOLTAGE

3-3

Run time: 12 minutes*

Run time: 24 or 60 minutes*

3-4

Parking lights flashing

Parking lights constant

3-5

Crank time 0.6 seconds

0.8, 1.0, 1.2, 1.6, 1.8, 2.0, 4.0

3-6

Voltage check - high

Voltage check - low

3-7

Auxiliary output - factory disarm

Special accessory

3-8

Status output

Factory re-arm output

3-9

Anti-grind ON

Anti-grind OFF

menu #3 - remote start options

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды