Avital AviStar 3300 страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 50

background image

14

© 2000 Directed Electronics, Inc. Vista, CA

Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in the dash-

board. In most diesels the wire is negative (ground turns on the bulb) and the GRAY/BLACK wire can be directly

connected to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the bulb) a relay must

be used to change the polarity. Here are some common colors of this wire:

■

Chevrolet and GMC trucks - Light blue or dark blue

■

Ford Trucks - Black/pink

■

Dodge Ram Trucks - Orange/black or black/orange

NOTE!

A 1-amp diode must be installed in line on the factory wire between the wait-to-start indi-

cator and the ECM. (See the following diagram for details.)

H2/3 GRAY/BLACK (-) diesel wait-to-start bulb input

«
...
12
13
14
15
16
...
»

Содержание AviStar 3300



















































Отзывы:

Нет отзывов

Похожие инструкции для AviStar 3300

Бренд: Quell Страницы: 14

Бренд: La Crosse Technology Страницы: 9

Бренд: Greenheck Страницы: 7

Бренд: La Crosse Technology Страницы: 20

Бренд: GE Страницы: 13

Бренд: Honeywell Home Страницы: 4

Бренд: CrimeStopper Страницы: 1

Бренд: CrimeStopper Страницы: 3

Бренд: CrimeStopper Страницы: 3

Бренд: DM TECH Страницы: 3

Бренд: La Crosse Страницы: 2

Бренд: La Crosse Страницы: 10

Бренд: Black Widow Страницы: 8

Бренд: JVD Страницы: 38

Бренд: Masterbuilt Страницы: 16

Бренд: Telefunken Страницы: 18

Бренд: Gasmate Страницы: 20

Бренд: Krown Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды