Avital AviStar 3300 Скачать руководство пользователя

Страница: 37 / 50

NOTE:

Some features have more than two possible settings. Pressing Channel One will select the one

chirp setting, pressing Channel Two will toggle through the two-chirp and higher settings.)

Release.

Release the Valet/Program switch.

Once a feature is programmed:

■

Other features can be programmed within the same menu.

■

Another menu can be selected.

■

The learn routine can be exited if programming is complete.

To access another feature in the same menu:

1. Press and release the Valet/Program switch the number of times necessary to advance from the feature you

just programmed to the next one you want to program.

2. Then press the Valet/Program switch once more and

HOLD

it.

For example, if you just programmed the third feature in the menu and you would like to program the seventh

feature in the menu, you would press and release the Valet/Program switch four times and then press it once more

and

HOLD

it. The siren would chirp seven times to confirm access to the seventh feature.

To select another menu:

1. Press and

HOLD

the Valet/Program switch.

2. After three seconds, the unit will advance to the next menu and the siren will chirp, indicating which menu

has been accessed.

For example, if you just programmed some features in the first menu and you want to program a feature in the

third menu, press and

HOLD

the Valet/Program switch. After three seconds, the siren chirps twice indicating

access to the second menu. Continue to

HOLD

the button and three seconds later the siren will chirp three times

indicating access to the third menu. Features in the third menu are then programmable following steps 4 through

6 of the System Features Learn Routine procedure.

To exit the learn routine:

The learn routine will be exited if any of the following occurs:

1. Close the open door.

2. Turn the ignition on.

3. There is no activity for longer than 15 seconds.

4. The Valet®/Program switch is pressed too many times.

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды