Avital AviStar 3300 страница 46 Скачать руководство пользователя

Страница: 46 / 50

shutdown diagnostics

To perform shutdown diagnostics:

1. With the ignition OFF, press and hold the Valet/Program button.

2. Turn the ignition ON and then back OFF while holding the Valet/Program button.

3. Release the Valet/Program button.

4. Press and release the Valet/Program button. The LED will report the last shutdown for one minute or until

the ignition is turned on.

rapid resume logic

The Rapid Resume Logic feature ensures that when the security system is powered back up after power has been

disconnected, the system will resume the same state it was in before power was lost. For example, if power is

disconnected during a full trigger sequence, the system will still be in the full trigger sequence when power is

reconnected to the unit. If power is disconnected while the unit is disarmed, it will still be disarmed when power

is restored.

LED FLASHES

SHUTDOWN MODE

One

Timed out

Two

Over-rev shutdown

Three

Low or no RPM

Four

Transmitter shutdown (or optional push-button)

Six

(-) Shutdown (H3/3 GRAY) or (+) Shutdown (H3/4 BROWN)

Seven

(-) Neutral safety shutdown (H3/6 BLACK/WHITE)

Eight

Wait-to-start timed out

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды